Additional information Troubleshooting, Noise | Pioneer VSX-D811S

10 Additional information

Troubleshooting

Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.

Problem

Remedy

The power does not turn on.

•Connect the power plug to the wall outlet.

•Disconnect the power plug from the outlet, and insert again.

•Make sure there are no loose strands of speaker wire touching the rear panel. This could cause the receiver to shut off automatically.

No sound is output when a function is selected.

•Make sure the component is connected correctly (refer to pages 14–19).

•Press MUTE on the remote control to turn muting off.

•Adjust the MASTER VOLUME.

•Press the MONITOR button to turn monitoring off.

No image is output when a function is selected.

•Make sure the component is connected correctly (refer to pages pages 14–19).

•Select the correct component (use the MULTI JOG/INPUT SELECTOR dial or the MULTI CONTROL buttons on the remote).

Considerable noise in radio	• Tune in the correct frequency.
broadcasts.	• Connect the antenna (refer to page 19).
	• Route 2 RF and digital cables away from the antenna
	terminals and wires.
	• Fully extend the FM wire antenna, position for best reception,
	and secure to a wall.
	• Connect an outdoor FM antenna (refer to page 19).
	• Adjust the direction and position for best reception.
	• Connect an additional internal or external AM antenna (refer
	to page 19).
	• Turn off the equipment causing the noise or move it away from
	the receiver.
	• Place the antenna farther away from the equipment causing
	the noise.

Broadcast stations cannot be	• Connect an outdoor antenna (refer to page 19).
selected automatically.

68

En

XRB3013A.68.74

68

01.12.12, 5:13 PM

Image 68

Pioneer VSX-D811S, VSX-D711 manual Additional information Troubleshooting, Adjust the Master Volume, Receiver, Noise

Contents

VSX-D711 VSX-D811S Important Notice XRB3013A.01.06 01.12.12, 441 PM Contents Making a recording Installing the receiver Operating range of remote control unitBefore you start Checking what’s in the box Making cable connections Minute guide Introduction to home theater Hook up your TV 02 5 minute guide Listening to Surround SoundHook up your DVD player Minute guide Connect your speakers 02 5 minute guide SBL SBR Play a DVD, and adjust the volume to your liking 02 5 minute guide Using the Quick Setup Press Quick Setup1ch 0ch Connecting up Audio/Video cordsVideo cables Component video cords Connecting up Connecting digital components VSX-D711 VSX-D811S Connecting up Connecting audio components CD player Connecting up Connecting DVD 5.1 channel components Video Connecting up Connecting video components Connecting to the front panel video terminal AM loop antenna Connecting up Connecting antennasFM wire antenna Connecting up Connecting the speakers VSX-D711 Be sure to complete Connecting up Connecting the speakers VSX-D811STo 16 Ω B speaker systems Hints on speaker placementSpeaker terminals View of speaker set up VSX-D811S Connecting up Connecting additional amplifiers VSX-D811S only Connecting up AC outlet Operating other Pioneer componentsAppliance to this Units AC Outlet Control OUT terminal Master Volume Controls and Displays Front panelSTANDBY/ON Enter Controls and Displays Display Analog DTSPRO Logic ATT Controls and Displays Remote control SourceRCV DISPLAY/DISC Enter DTV Info DTV ON/OFFDTV Menu TOP Menu TV Volume + MuteTV Input LED Display Stereo/Direct Standard modePlaying sources Introduction to Sound Modes Playing sources Advanced Surround modesSources with stereo surround Analog 2-channel stereo source Playing sources Choosing the input signal Listening to multi-channel playback Using Stereo/Direct Using Advanced SurroundNEO6 Start playback of the component you selected in step Playing sources Using Loudness and Midnight listening Using the tone controlsPlaying other sources Treble Playing sources Selecting the multi-channel analog inputs DVD Setting up the receiver Choosing your receiver setup Setting up the receiver Speaker settingFL-C FS-CS-S FL-CS-SFL-CL-SL FL-CS-SS FL-CL-SS FL-CS-SL FL-CL-S Surround back speaker setting Channel settingSubwoofer setting Crossover frequency setting Center speaker distance setting LFE attenuator settingFront speaker distance setting Surround speaker distance set- ting Surround back speaker distance setting Dynamic range control settingDual mono setting Component video input settings Surround back channel input setting Coaxial digital input settingsOptical digital input settings SB 2ch Use ’ or ‘ to select SB 2ch in or SB 1ch Setting the relative volume level of each channel Use Level +/- to adjust the speaker levels in turnWhen you’re done, press Test Tone to turn off the test tone FL C FR SW SL SB Improving FM stereo sound Using the tuner Listening to the radioTuning directly to a station Using the tuner Saving station presetsTune to a station you want to memo Rize Press T.EDIT Tuner Edit Using the tuner Naming station presets Listening to station presetsChoose the station preset you want to name Input the name you want Making Recordings Making an audio or a video recording Monitoring your recording Setting the remote to control other components Selecting preset codes directly Searching for preset codes Programming signals from other remote controlsSwitch on the component you want to control Press Remote Setup and hold for three seconds Erasing one of the remote control button settings Clearing all the remote control settingsPrepare the remote to erase the button setting Press and hold the button to be erased for three seconds Confirming preset codes Direct function Controlling the rest of your system Controls for TVs ChannelTV VOL SUB Title Controlling the rest of your system Controls for other components Enter Channel DisplayMenu Controlling the rest of your system Preset Code List Manufacturer Code 1055, 1086, 1089 1013, 1019, 1026, 10271032, 1063 1036, 1086 1096 1114 1013, 10191017, 1032, 1089 1014 1059 1006, 10791132 1055, 1073 CD Player MD PlayerLD Player Tape Deck DVD Player Receivers AmplifierMisc Audio VCR 2015, 2027, 2032 2015, 20422017, 2018, 2053 2001, 2017, 2034, 2059 2062, 2085, 2087 Satellite Tuner 4015 40084005 4034 Cable TV Additional information Troubleshooting Adjust the Master VolumePlace the antenna farther away from the equipment causing Receiver Additional information Front panel refer toRemove the obstacle or operate from another position Light Additional information Specifications Amplifier SectionVideo Section FM Tuner Section Miscellaneous Furnished Parts We Want You Listening For a Lifetime Additional information Additional information Additional information 0 4 2 1 1 4 0 TNGZF/01L00001 Printed XRB3013-A