Manuals / Brands / Computer Equipment / Switch / Planet Technology / Computer Equipment / Switch

Planet Technology WGSW-2620P 4.7.4 Port Controls, In:, Out:, State:, Speed:, Duplex:, Priority:, Security:, Band Width:, Negotiation:, Flows Control:, Back Pressure:

1 131

Download 131 pages, 1.83 Mb

Console Port Information interface

4.7.4 Port Controls

You can change the port status.

1Select the port by scroll the list in Port column.

2State: User can disable or enable this port control.

3Negotiation: User can set auto negotiation mode is Auto, N-way (specify the speed/duplex on this port and enable auto-negotiation), Force of the port.

4Speed: set the speed of each port.

5Duplex: set full-duplex or half-duplex mode of the port.

6Flows Control: set flow control function is ON or OFF in Full Duplex mode.

7Back Pressure: set Back Pressure is ON or OFF in Half Duplex mode.

8Band Width: The port1 ~ port 8, supports port ingress and egress rate control. For example, assume port 1 is 10Mbps, users can set it's effective egress rate is 1Mbps, ingress rate is 500Kbps. The switch will perform flow control or Back Pressure to confine the ingress rate to meet the specified rate.

。In: fill in the port effective ingress rate. The valid range is 0 ~ 999. The unit is 100K. 0: disable

rate control. 1 ~ 999: valid rate value.

。Out: fill in the port effective egress rate. The valid range is 0~999. The unit is 100K. 0: disable

rate control. 1 ~ 999: valid rate value.

9Priority: this static priority based on port, if you set the port is high priority, income frame from this port always high priority frame.

10Security: when the port is in security mode, the port will be "locked" without permission of address learning. Only the incoming packets with SMAC already existing in the address table can be forwarded normally. User can disable the port from learning any new MAC addresses, and then use the static MAC addresses screen to define a list of MAC addresses that can use the secure port.


11	Click	Apply	button to apply all configuration.
11	Click		button to apply all configuration.
12	When you select the port, you can see port current configure shows in below.

Port Control interface

Contents

Page Trademarks Disclaimer FCC Warning CE Mark Warning Revision Table of Contents 6. Appendix 1. INTRODUCTION Model WGSW-2620PV Page 2. INSTALLATION 2.1.1 Product Overview 2.1.2 Switch Front Panel 2.1.3 LED Indications LED Color Function 2.2.1 Desktop Installation 2.2.2 Rack Mounting Step6: 3.CONSOLE MANAGEMENT 3.3.1 Commands Level ups exit poe 3.3.2 Commands Set List 3.3.2.1 System Commands Set default default username [user-name] username password 3.3.2.2 Port Commands Set moduleEthernet 1/1 duplex full duplex [full | half| auto] flowcontrol on or no flowcontrol flowcontrol on security on or no security Bandwidth [in | out] [value] bandwidth hi State [Enable | Disable] 3.3.2.3 Trunk Commands Set 3.3.2.4 VLAN Commands Set vlanmode [disable| portbase| 802.1q | vlanmode 802.1q gvrp] Port Base VLAN vlan [group name] delete [port ID] delete no vlan [Group name] or Page vlanidrang vlanidrange [VLANidrange] VLAN protocol [Groupname] add [portNumber] tagged [Groupname] delete 3.3.2.5 Spanning Tree Commands Set spanning-tree[on off] or no spanning-treeon spanning-treepriority priority [number] hello-time [seconds] hello-time3 interface fastEthernet stp-path-cost forward-time forward-time20 3.3.2.6 QoS Commands Set qos level [priority] enable level 2,3 enable no qos level no qos 3.3.2.7 IGMP Commands Set 3.3.2.8 Mac / Filter Table Commands Set 3.3.2.9 SNMP Commands Set 3.3.2.10 Port Mirroring Commands Set no port monitor monitor both port monitor show port monitor 3.3.2.11 802.1x Commands Set sharekey [Sharekey] system sharekey serverport [Port system serverport 8021x misc txperiod [TXPeriod value] misc txperiod no 8021x txperiod supptimeout [SEC] reauthperiod [SEC] misc reauthperiod reauthperiod „ Reject: the „ Accept: the 3.3.2.12 TFTP Commands Set 3.3.2.13 UPS Commands Set 3.3.2.14 POE Commands Set setlimit setlimit setps1 setps1 portebl portebl 3.4 Menu Management 3.4.1Status and Counters 3.4.1.1 Port Status 3.4.1.2 Port Counters 3.4.1.3 System Information 3.4.2 Switch Configuration 3.4.2.1 Administration Configuration 3.4.2.1.1 Device Information 3.4.2.1.2 IP Configuration 3. 4.2.1.3 User Name Configuration 3.4.2.1.4 Password Configuration 3.4.1.4.5 SNTP Configuration 3.4.1.4.6 Syslog Client Configuration 3.4.2 Port Configuration 3.4.3 Trunk Configuration 3.4.4 Port Mirroring Configuration 3.4.5 VLAN Configuration 3.4.5.1 VLAN Configure 3.4.5.2 Create VLAN Group Create 802.1Q VLAN Enable security VLAN setting: 3.4.5.3 Edit / Delete VLAN Group Group Sorted Mode Name VLAN ID 3.4.6 Priority Configuration 3.4.7 MAC Address Configuration 3.4.7.1 Static MAC Address 3.4.7.2 Filtering MAC Address Add the Filtering MAC Address Edit Filtering MAC address 3.4.7.3 Misc Configuration 3.4.8 Protocol Related Configuration 3.4.8.1 STP 3.4.8.1.1 STP Setup 3.4.8.1.3 Per Port Setting 3.4.8.1.2 System Configuration 3.4.8.2 SNMP 3.4.8.2.1 SNMP System Options 3.4.8.2.2 Community Strings 3.4.8.2.3 Trap Managers Add the trap manager IP: Delete Trap Manager 1.Select <Delete 3.4.8.3 LACP 3.4.8.3.1 Working Ports Setting 3.4.8.3.2 LACP State Activity 3.4.8.3.3 LACP Group Status 3.4.8.4 IGMP/GVRP Configuration 3.4.8.5 802.1x Configuration 3.4.8.5.1 802.1x Setup 3.4.8.5.2 System Configuration 3.4.8.5.3 Per Port Setting 3.4.8.5.4 Misc Configuration 3.4.9 System Reset Configuration 3.4.9.1 Factory Default 3.4.9.2 System Reboot 3.4.9.3 TFTP Configuration 3.4.9.3.1 TFTP Update Firmware 3.4.9.3.2 TFTP Restore Configuration 3.4.9.3.3 TFTP Backup Configuration 3.4.10 UPS Menu 3.4.11 POE Menu Port Enable: PwrLimitClass.: PwrLimitManag.: Detect Legacy: PowerLimitMax: R detect: Dsvry R (ohms): Port Curr (mA): Port Volt (V): Port Pwr (W): 3.4.12 Save Configuration 3.4.13 Xmodem Upgrade Page 4. WEB-BASEDMANAGEMENT 4.4 System Login "http: "admin "OK 4.5 Port status 4.5.1 View the Port Information 4.7.1 IP Address 4.7.2 Switch Setting 4.7.2.1 Basic 4.7.2.2 Advanced Setting 4.7.2.3 Misc Configuration 4.7.3 Console Port Information 4.7.4 Port Controls 4.7.5 Trunking 4.7.5.1 Aggregator setting 4.7.5.2 Aggregator State Activity 4.7.6 Forwarding and Filtering 4.7.6.1 IGMP Snooping 4.7.6.2 Static MAC Address MAC filtering MAC Address 4.7.7 VLAN configuration 4.7.7.1 Port-basedVLAN Page 4.7.7.2 802.1Q VLAN Basic Group Name: Page Tag: Untag: Port VID: Ingress Filtering: Enable: 4.7.8 Spanning Tree 4.7.8.1 System Configuration 4.7.8.2 Per Port Configuration 4.7.9 Port Mirroring System Options Community strings: serve as password Strings: RO: RW: Trap Manager 4.7.11 Security Manager 4.7.12 Save Configuration 4.7.13 SNTP Configuration 4.7.14 802.1X Configuration 4.7.14.1 System Configuration 4.7.14.2 Per port Configuration 4.7.14.3 Misc Configuration 4.7.15 System Log 4.8 TFTP Update Firmware TFTP Server IP Address: 4.9.1 TFTP Restore Configuration 4.9.2 TFTP Backup Configuration 4.10 Factory Default 4.11 System Reboot 4.12 UPS Status UPS information: Input Voltage: Output Voltage: Battery Capacity: 4.13 POE Status Firmware: Total Power (W): Port: Power Limit by Classification: Power Limit by Management: Detect Legacy Signature: 5. TROUBLESHOOTING 5.1.1 Faulty or loose cables 5.1.2 Non-standardcables 5.1.3 Improper Network Topologies 5.2.1 Cabling 5.3.1 No Power Forward 6. Appendix Cable Type Max. Length Connector 6.2 100BASE-TX/10BASE-TPin Assignments RJ-45Pin Assignments Pin Number Assignment Note: