Manuals / Porter-Cable / Power Tools / Saw

Porter-Cable 33-413 Constructing A Push Stick, Pushstick, Notchto, helpprevent, handfromslipping

Models: 33-412

1 28

Page 23

CONSTRUCTING A PUSH STICK

When ripping work less than 4 inches wide, a push stick should be used to complete the feed and could easily be made from scrap material by following the pattern shown in Fig. 58.

PUSHSTICK

Makefrom1/2″ OR3/4″WOOD orthicknesslessthan widthofmaterialtobecut.

Notchto

helpprevent

handfromslipping

Cutheretopush 1/4″ wood.

Cutheretopush 1/2″ wood.

1/2″ Squares

Fig. 58

Page 23

Image 23

Porter-Cable 33-413 Constructing A Push Stick, Pushstick, Notchto, helpprevent, handfromslipping, Cutheretopush 1/4″ wood

Contents

INSTRUCTION MANUAL For Parts, Service, Warranty or other Assistanceplease call 1-800-223-7278 In Canada call 14, 16, and 18 Long Arm Radial SawsSAVE THESE INSTRUCTIONS TABLE OF CONTENTSIMPORTANT SAFETY INSTRUCTIONS back coverCALIFORNIA PROPOSITION SAFETY GUIDELINES - DEFINITIONS6. CHECK FOR DAMAGED PARTS. Before using the GENERAL SAFETY RULESIMPORTANT SAFETY INSTRUCTIONS ALWAYS USE SAFETY GLASSES. EverydayFAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY 3. FOLLOW ALL WIRING CODES and recommended electrical connectionsSAVE THESE INSTRUCTIONS Refer to them often and use them to instruct othersFUNCTIONAL DESCRIPTION CARTON CONTENTSPOWER CONNECTIONS MOTOR SPECIFICATIONSA B M E UNPACKING AND CLEANINGGUIDE TO PARTS UNPACKING AND ASSEMBLING LEGS TO BASE ASSEMBLYASSEMBLY TOOLS REQUIRED ASSEMBLY TIME ESTIMATE-4 to 6 hours SELECTING FLOOR SPACEF E D CUTTINGHEAD AND CROSS-CUT STOP TO TRACK-ARMD E B STARTER BOX TO BASETABLE BOARDS AND FENCE C A B E ADJUSTING TABLE TOP PARALLEL TO TRACK-ARMBLADE GUARD AND ANTI KICKBACK DEVICE H F G CUTTERHEAD RETURN SPRINGB B C D OPERATION OPERATIONAL CONTROLS AND ADJUSTMENTSLOCKING SWITCH IN “OFF” POSITION MAKE SURE THAT THE SWITCH IS INTIGHTENING YOKE AGAINST BEARING CARRIAGE ADJUSTING BALL BEARINGS AGAINST TRACK RODSDISCONNECT MACHINE FROM POWER SOURCE TAKING SIDE MOTION OUT OF OVER-ARMDISCONNECT MACHINE FROM POWER SOURCE ADJUSTING TRACK RODSDO NOT OVER TIGHTEN BOLT D ADJUSTING BLADE SQUARE WITH TABLE TOPADJUSTING BEVEL CLAMP HANDLE ADJUSTING TRACK-ARM CLAMP HANDLEDISCONNECT MACHINE FROM POWER SOURCE ADJUSTING SAW TRAVEL SQUARE WITH FENCEG H C B A DISCONNECT MACHINE FROM POWER SOURCE ADJUSTABLE CROSS-CUT STOPREMOVING HEELING IN SAW CUT CLOCKWISEDISCONNECT MACHINE FROM POWER SOURCE ADJUSTING BLADE GUARDCHECKING AND ADJUSTING AUTOMATIC BRAKE DISCONNECT MACHINE FROM POWER SOURCEAUXILIARY TABLE BOARD FACING ADJUSTING TENSION ON CUTTINGHEAD RETURN ASSEMBLYUSING A TABLE EXTENSION WRENCH STORAGE BRACKETSMITER CUTTING MACHINE USECROSS-CUTTING CROSS-CUT STOPIN-RIPPING COMPOUND MITER CUTTINGRIPPING OUT-RIPPINGhelpprevent CONSTRUCTING A PUSH STICKPUSHSTICK NotchtoKEEP MACHINE CLEAN TROUBLESHOOTING GUIDEMAINTENANCE SERVICETwo Year Limited New Product Warranty ACCESSORIESWARRANTY Page Page CENTROS DE SERVICIO DE PORTER-CABLE DELTA PORTER-CABLE DELTA SERVICE CENTERSCANADIAN PORTER-CABLE DELTA SERVICE CENTERS