Diagram | Precor C936i specification

C O M M E R C I A L P R O D U C T S D I V I S I O N

Diagram 3	Lift the rear of the
	unit and roll it to
	its assembly
	location.
	Rear cover of unit

Lift the unit by placing hands on opposite sides of the rear cross brace found under treadmill’s running belt.

3.Move the treadmill. Diagram 3.To properly lift the rear end and roll it on its front wheels, review Diagram 3. To avoid injury to yourself or damage to the unit, ask for help in placing the treadmill where you plan to use it.

Diagram 4	Remove the
	shipping
	fasteners from
	the front plate.
	Shipping
	fasteners found
	on right and left
	sides of the front
	panel.
	Front panel

4.Remove the shipping fasteners from the front panel. Diagram 4.With the supplied hex key and a ½-inch box end wrench, loosen and remove the four bolts, washers and nuts on the front panel.These fasteners are used during shipping to hold the front panel in place. Discard the fasteners.

5.Remove any tape or wire ties that secure the display cable to the side of the unit.

CAUTION:To avoid damage to the display cable, read the following steps carefully. Damage to the cable due to improper assembly is not covered by the Precor LimitedWarranty.

page 12

Image 12

Precor C936i owner manual Diagram

Contents

M M E R C I a L P R O D U C T S D I V I S I O N Important Safety Instructions Safety Approval Grounding Instructions Table of Contents Maintenance Exercising on the Treadmill Radio Frequency Interference RFI European ApplicationsVoid the user’s authority to operate the equipment Obtaining Service About this Manual M M E R C I a L P R O D U C T S D I V I S I O N Unpacking the Treadmill Standard EquipmentOther Equipment Hardware KIT Additional Tools Needed Setting Up the Treadmill Installation RequirementsAssembly Instructions Diagram Route cable Secure the display console to the upright supports. Diagram Csafe Diagram Attach handrails to the side and base brackets. Diagram Perform steps a. and b. on the opposite side Test the heart rate feature. Diagram Install handrail First Tighten Level Unit Turning the Unit on and OFF Checking the Alignment of the Running Belt If the running belt Then Changing the Club Settings Club Information Display key functions within the Club Custom Mode Determining the Units of Measure Setting a Workout Time Limit Setting a Pause Time LimitDetermining the Club Speed Limit To 18 kph M M E R C I a L P R O D U C T S D I V I S I O N Using Csafe Standard Equipment User ID Entry Program Keys Features on the Display Console C936i Display Setup Mode and Prompts Smartrate Display Setup Mode and the Quickstart Feature Weight prompt Following occursPress Quickstart at Precor banner Display Features During a Workout M M E R C I a L P R O D U C T S D I V I S I O N Keys on the Display Console Keypad keys Quickstart DefaultValues Prompts Default Value Changing the Display Features Using the Select KEY Using the Security Clip Using the HandrailsUsing the Heart Rate Touch Capability Exercising on the Treadmill Keypad Tips Workout TipsQuick Steps to Working OUT Continue your workout Cooling Down After a Workout Red Stop button PAUSE, Workout SUMMARY, and Exit Features Stop Heart Rate Feature Using the Smartrate FeaturePrograms Manual Mode and the Quickstart KEY 200 190 180 170 160 150 140 130 120 110 100 Cross Country Program Interval ProgramTo use the interval program, take the following steps Weight Loss Program Random Program Heart Rate Program Maintenance Cleaning the EquipmentInspection Perform a daily inspection of the treadmill Aligning the Running Belt Storing the Chest Strap Servicing the TreadmillLong Term Storage Thank You and Welcome to Precor Date of Purchase Purchased from Dealer name Product Serial NumbersPlease indicate the type and number of products purchased How many members do you have? Limited Warranty Warranty Periods and CoverageConditions and Restrictions Complete this portion and keep for your records Product Specifications Electronic Specifications