
Interface Related Features
Keyboard Wedge/USB Keyboard — cont.
Intercharacter Delay
This feature does not apply to the USB Keyboard interface.
NOTE
START |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
MODE |
|
|
|
|
|
|
| BARCODE | ||||||||||||||
|
| |||||||||||||||||||||
| between scancodes within each character. If the trans- | |||||||||||||||||||||
| mission speed is too high, the system may not be able | |||||||||||||||||||||
| to receive all characters. You may need to adjust the | |||||||||||||||||||||
| delay to make the system work properly. Selectable | |||||||||||||||||||||
| from 00 to 255 in 10msec increments. Use hexidecimal | |||||||||||||||||||||
| (range: 00 to FF hexidecimal) to set the delay. | |||||||||||||||||||||
| To configure this feature, scan the “START” bar code | |||||||||||||||||||||
| above to place the unit in Programming Mode, then the | |||||||||||||||||||||
| “Set Intercharacter Delay,” followed by the digits from | |||||||||||||||||||||
| the Alphanumeric table in Appendix C, Alpha- | |||||||||||||||||||||
| Numeric Pad representing your desired length. Exit | |||||||||||||||||||||
| programming mode by scanning the “END” barcode | |||||||||||||||||||||
| below | |||||||||||||||||||||
| DEFAULT SETTING FOR THIS FEATURE: | |||||||||||||||||||||
|
|
|
|
|
| 00 (No Delay) | ||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Set |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Intercharacter |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Delay |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
END |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PowerScan® 7000 Linear Imager |