Q-Logic ISR6152 - page 88

3–Viewing Router Information

FCIP Routes

3-42 ISR645610-00 B

VLAN Enabled indicates whether the use of virtual LANs is enabled or

disabled. The default is Disabled.

VLAN ID specifies the VLAN ID assigned to the FCIP route when VLAN use

is enabled. The VLAN ID segregates traffic in a LAN, and must be the same

on both routers participating in the FCIP route (local and remote routers

must be using same VLAN ID) and on the Ethernet switches.

VLAN Priority specifies the priority of the VLAN assigned to the FCIP route

when VLAN use is enabled. In a network with multiple VLANs, the VLAN

Priority box prioritizes Ethernet traffic by giving higher preference to traffic

in the network over non-VLAN traffic and traffic from VLANs with lower

priorities. Level 1 is the lowest priority, level 7 is the highest priority, and level

0 specifies no VLAN.

Error Detect Timeout sets the error detect timeout value by selecting one

of five options: 1 to 5 seconds. The default is one second.

Resource Allocate Timeout sets the resource allocate timeout value to one

of five options: 1 to 5 seconds. The default is one second.

FCIP Timestamp enables or disables FCIP timestamps. The default is

Enabled.

FCIP SW Compression indicates whether software compression is

enabled, disabled, or automatic (the default is Disabled). Depending on the

data, software compression may result in lower bandwidth operations. If the

data are highly compressible, the compressed FCIP PDU is significantly

smaller than the original Fibre Channel frame.

Bandwidth (Mbit/sec) defines the maximum bandwidth (in megabits per

second) the GbE port will use during transmits. Supported values range from

1 to 1000 Mbps. Use this setting to limit the bandwidth used by the FCIP

route so it does not consume all the available link bandwidth. For example, if

the slowest link in the WAN is a DS-3 link, the maximum available bandwidth

is 45 megabits per second. To limit the FCIP route to 33 percent of the

overall link bandwidth, set the bandwidth to 15 megabits per second.

Statistics

The Statistics page for FCIP routes lists parameters and values, as shown in

Figure 3-28. To update the statistics, click Refresh. To reset all values to zero,

click Clear.

Contents

Main Document Revision History Table of Contents Preface 1 Getting Started 2 Understanding the User Interface 3 Viewing Router Information 4 Viewing Service Information A Simple Network Management Protocol (SNMP) B Log Messages Index List of Figures List of Tables Preface Intended Audience Whats in this Guide Whats in the Help System Related Materials Documentation Conventions Page Figure i. Example: Jagged Edges Depict Partial Interface License Agreements Technical Support Training Contact Information Knowledge Database 1 System Requirements Connecting the Management Workstation to the Router Connecting the Hardware Setting the Workstation IP Address Configuring the Router Ports Updating the Firmware Starting SANsurfer Router Manager Starting SANsurfer Router Manager on Windows Starting SANsurfer Router Manager on Linux or Solaris Starting SANsurfer Router Manager on Macintosh Connecting SANsurfer Router Manager to the Router Figure 1-1. Connect to Router Dialog Box Getting Help Viewing the Help System Specifying the Help Browser Figure 1-2. Browser Location Dialog Box Viewing SANsurfer Router Manager Information Figure 1-3. About SANsurfer Router Manager Box Setting Security Figure 1-4. Setting System Security Refreshing the Host Configuration Figure 1-5. Refresh Dialog Box Exiting SANsurfer Router Manager Page 2 Main Window Figure 2-1. SANsurfer Router Manager Interface Menu Bar File Menu Table 2-1. Interface Description View Menu Settings Menu Wizards Menu Page Help Menu Toolbar Shortcut Menus Table 2-2. Toolbar Buttons Page Table 2-3. Shortcut Menu Options Table 2-3. Shortcut Menu Options (Continued) Option Description Tree Pane Router Tree Table 2-3. Shortcut Menu Options (Continued) Figure 2-3. Router Tree Pane (Example) Figure 2-4. Component Information Pane (Example) Services Tree Figure 2-5. Services Tree Pane (Example) Status Icons and Text Router Tree Icons Router FC and iSCSI Ports VP Groups Discovered FC and iSCSI Initiators FC and iSCSI Discovered Targets iSCSI Presented Targets FCIP Routes Arrays Services Tree Icons Page Page 3 Router iSR6152 Basic Information Figure 3-1. Router Information: Basic Information Page Page Page Management Information Figure 3-2. Router Information: Management Information Page Page NTP Server Information Figure 3-3. Router Information: NTP Server Information Page Security Figure 3-4. Router Information: Security Page SNMP Management Figure 3-5. SNMP Management Page SNMP Configuration Enabled SNMP Trap Receivers Features Figure 3-6. Features Page FC Ports Figure 3-7. FC Port: Information Page Advanced Configuration Figure 3-8. FC Port: Advanced Configuration Page Page Figure 3-10. FC Port: Performance Page iSCSI Ports Figure 3-11. iSCSI Port: Information Page iSCSI Port Information iSCSI Port Network Settings iSNS Advanced Configuration Figure 3-12. iSCSI Port: Advanced Configuration Page Page Page VP Groups Discovered FC Initiators Figure 3-15. Discovered FC Initiators: Information Page LUN List Figure 3-16. Discovered FC Initiators: LUN List Page Discovered iSCSI Initiators Figure 3-17. Discovered iSCSI Initiators: Information Page LUN List Figure 3-18. Discovered iSCSI Initiator: LUN List Page FC Discovered Targets FC Presented Targets Figure 3-19. FC Discovered Targets: FC Presented Targets Page iSCSI Presented Target List Figure 3-20. FC Discovered Targets: iSCSI Presented Target List Page Figure 3-21. FC Discovered Targets: Information Page iSCSI Presented Target Figure 3-22. FC Discovered Targets: iSCSI Presented Target Page Discovered LUN Information Figure 3-23. FC Discovered Targets: Discovered LUN Information Page iSCSI Discovered Targets Figure 3-24. iSCSI Discovered Targets: Information Page Page Arrays Figure 3-25. Arrays: Information Page iSCSI Presented Targets Figure 3-26. iSCSI Presented Targets: Information Page FCIP Routes Page Page Page Page Page Page Page 4 Information Router iSR6152 Data Migration Info Figure 4-1. Data Migration Info Page Data Migration Jobs Active Data Migration Jobs Figure 4-2. Data Migration Jobs: Active Data Migration Jobs Page Synchronizing Jobs Figure 4-3. Data Migration Jobs: Synchronizing Jobs Page Completed Data Migration Jobs Figure 4-4. Data Migration Jobs: Completed Data Migration Jobs Page Page Page A Management Protocol (SNMP) Introduction SNMP Properties Table A-1. SNMP Properties Management Information Base (MIB) Table A-2. SNMP Trap Configuration Parameters Table A-1. SNMP Properties (Continued) System Information Network Port Table Page Fibre Channel Port Table Page Sensor Table Page Page Notifications Notification Objects Agent Start Up Notification Agent Shut Down Notification Network Port Down Notification Fibre Channel Port Down Notification Sensor Notification Generic Notification Page B Table B-1. iSR6152 Router Log Messages Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Glossary Page Page Page Page Page Page Page Page Page Index A B C D E F G H I Page J L M N O P R S T U V W X