CB 1200 Pellet Stove

R

2.Exhaust Blower Replacement

Remove existing blower:

a.Use proper shut down procedures to shut down the appli- ance and let it completely cool and then unplug it.

b.Use an 11/32" wrench or nut driver to loosen and remove the (6) nuts holding motor mount plate to the blower housing on your stove.

c.Remove washer from beneath the terminal ring on the grounding wire.

d.Pull motor/mounting plate from blower housing.

e.Scrape off old gasketing material from blower housing.

Install new blower:

f.The blower and blower housing is shipped as a unit. It is necessary to separate them at this point if you are using the existing blower housing already installed on the appliance:

g.Follow steps 2 and 3 above. Discard or set aside the new blower housing.

h.Carefully remove gasketing from new housing and set onto the blower housing.

Re-install blower to blower housing:

i.Install blower on housing ensuring that wiring exits facing the 8 o’clock position. Place the washer and then the grounding wire on nearest mounting plate stud.

j.Use nuts removed in step b to secure blower to hous- ing.

k.Re-connect wiring (use jumper wire if necessary). Re- connect power supply.

F.Baffle Removal

1.Use proper shut down procedures to shut down the appliance and let it completely cool down.

2.Open right side panel and then open the door.

3.The 2 baffles are located at the top inside of firebox.

4.Place your hand on the baffle and slide it up and the bottom edge will fall down and then you can lift the baffle out. Repeat for the other side.

G. Igniter Replacement

Igniter Bracket

 

Thumb Screw

Igniter

Figure 34.1

1.Use proper shut down procedures to shut down the appliance and let it completely cool down and then unplug it and remove the ash drawer.

2.Follow instructions to remove the ash pan found on page 30. Remove the access plate directly above it by removing the 2 screws just below the ash catcher.

3.The wire leads to the igniter are connected to the wire harness with 1/4 inch male / female spade connectors. These wires will pull forward approximately 4 to 5 inches (102mm to 127mm). Disconnect the spade connections and remove the igniter from the chamber. Loosen the thumb screw and slide igniter out.

4.Install new igniter into the chamber and tighten the thumb screw. Re-connect the wires to the 2 leads with the spade connectors.

5.Remove right side panel and pull wire leads back toward the rear of the appliance to take-up the 4 to 5 inches (102mm to 107mm) previously pulled out. This will keep the wires out of the way of the ash drawer. Double check that the igniter wires are clear of any movement, i.e. ash drawer, firepot cleaning rod, etc.

6.Re-install the ash drawer and side panel and re-connect the power.

Page 34

7014-179D

December 16, 2011

Page 33 Page 35
Page 34
Image 34
Quadra-Fire CB1200M-MBK owner manual Exhaust Blower Replacement Remove existing blower, Install new blower
Page 33 Page 35

CB1200M-MBK specifications

The Quadra-Fire CB1200M-MBK is a remarkable addition to the lineup of high-efficiency wood stoves, designed to provide exceptional heating performance while maintaining a user-friendly interface and aesthetic appeal. Known for its sleek design and modern technology, the CB1200M-MBK stands out as a powerful solution for both environmentally conscious homeowners and those in search of reliable warmth during cold months.

One of the main features of the CB1200M-MBK is its high efficiency rating, often exceeding 75%. This impressive figure is attributed to its innovative combustion technology, which maximizes wood-burning efficiency by promoting complete combustion. This means more heat is generated from less wood, translating to reduced emissions and less frequent refueling. This efficient design not only benefits the environment but also provides a cost-effective heating solution.

The CB1200M-MBK is equipped with a large firebox that can accommodate logs up to 18 inches long, allowing users to enjoy extended burn times and consistent heat output. With a capacity of up to 70,000 BTUs, this stove can efficiently heat spaces ranging from 1,000 to 2,200 square feet, making it suitable for a variety of home sizes.

Another standout feature is its advanced air control system, which provides precise control over combustion levels. This system enables users to adjust the air intake to optimize the fire's intensity, ensuring both comfort and efficiency. Additionally, the stove comes with a built-in ash pan, making cleanup easier and enhancing the overall user experience.

The CB1200M-MBK also showcases an appealing aesthetic, featuring a clean, modern design with a traditional cast-iron appearance. The durable, black finish offers an elegant touch, making it a stylish focal point in any room. Moreover, this model is designed to be compatible with various installation options, including top or rear venting, providing flexibility depending on the specific needs of the home.

Durability is another hallmark of the CB1200M-MBK, constructed with high-quality materials that ensure longevity and performance. The heavy-duty steel construction and quality ceramic glass withstand high temperatures and resist cracking, promising years of reliable use.

In conclusion, the Quadra-Fire CB1200M-MBK is a perfect blend of efficiency, performance, and style. With its impressive BTU output, advanced combustion technology, and user-friendly design, it stands as an ideal choice for homeowners looking to enhance their heating solutions while being mindful of environmental impacts.
Top Page Image Contents