CB 200 Pellet Stove | R |
|
|
| Reference Materials |
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| E |
|
|
|
| |
| Component Function & Location |
| When describing the location of a component, |
| ||||||
|
|
|
|
| ||||||
|
|
|
| it is always AS YOU FACE THE FRONT OF |
| |||||
A.11 |
|
|
|
|
|
| ||||
1. Control Box |
|
|
|
|
| THE APPLIANCE. |
|
| ||
| a. The control box is located under a small cover in the |
|
|
|
| |||||
7. Heat Exchangers |
|
| ||||||||
| right rear corner of the inside of the hopper. |
|
| |||||||
| b. There is a light located inside of the control box. The | The heat exchangers transfer hot air from the exhaust system | ||||||||
| into convection air. Lift the stove top to access the heat | |||||||||
| internal light will turn green when the appliance has | |||||||||
| reached a temperature of 200οF (93°C) in the firepot | exchangers. There are 2 clean out rods located under the | ||||||||
| and will turn red when it reaches 600oF (315°C). | heat exchangers. |
|
| ||||||
| c. There is also an internal blue light located in the upper | 8. Heat Output Switch |
|
| ||||||
| left corner of the control box. | When you plug in the | The heat output switch is located on the upper right side panel. | |||||||
| appliance the blue light will automatically start blinking | The function of the heat ouput switch is to regulate the burn | ||||||||
| 1 blink every 10 seconds for the first 60 seconds and | rates; low, medium, and high settings. | ||||||||
| then will stop. |
|
|
|
| 9. Hopper Switch |
|
| ||
|
|
|
|
|
|
|
|
| ||
| NOTE: |
|
|
|
| The hopper switch is located in the upper right hand corner | ||||
| Do NOT open the control box. This will void the |
| of the hopper. This switch is designed to shut down the feed | |||||||
| warranty. If you need to plug in or remove the control |
| motor whenever the hopper lid is opened. | |||||||
| box you must first unplug the appliance. |
|
| 10. Igniter |
|
| ||||
|
|
|
|
|
|
| The igniter is mounted on the base of the firepot. Combustion | |||
| 2. Convection Blower |
|
|
| ||||||
|
|
|
| air travels over the red hot igniter creating super heated air | ||||||
| The convection blower is mounted at the bottom rear of the | that ignites the pellets. |
|
| ||||||
|
|
|
|
| ||||||
| appliance. There are 2 impellers, one on each side of the | 11. Junction Box And Wiring Harness | ||||||||
| motor. The convection blower pushes heated air through the | The junction box is located on the right side of the appliance, | ||||||||
| heat exchange system into the room. |
|
| |||||||
|
|
| behind the interior shield. The junction box and wiring harness | |||||||
| 3. Combustion (Exhaust) Blower |
|
|
| ||||||
|
|
|
| are replaced as one component. | ||||||
| The combustion blower is mounted on the lower left side | 12. Power Supply |
|
| ||||||
| on rear of appliance. The blower is designed to pull the | The power outlet is located on the back of the appliance, | ||||||||
| exhaust from the appliance and push it out through the | |||||||||
| lower right corner. Check the wall receptacle for 120 volt, | |||||||||
| venting system. |
|
|
|
| |||||
|
|
|
|
| 60 Hz (standard current). Make sure the outlet is grounded | |||||
| 4. Feed System |
|
|
|
| |||||
|
|
|
|
| and has the correct polarity. | A good surge protector is | ||||
| The feed system is located in the hopper under the feed | recommended. |
|
| ||||||
|
|
|
|
| ||||||
| motor cover box on the left side of the appliance and can | 13. Red Call Light |
|
| ||||||
| be removed as an entire assembly. The assembly includes | The red call light is on the front of the junction box, next to the | ||||||||
| the feed motor, mounting bracket, bearing and feed spring | |||||||||
| reset button. The function of the red call light is to indicate | |||||||||
| (auger). The hollow feed spring (auger) pulls pellets up the | |||||||||
| that the thermostat is calling for heat. | |||||||||
| feed tube from the hopper area and drops them down the | |||||||||
| 14. Reset Button |
|
| |||||||
| feed chute into the firepot. |
|
|
|
|
| ||||
| 5. Firepot |
|
|
|
| The reset button is located on the right side of the apppliance | ||||
| The firepot is made of high quality ductile iron and has a | next to the red call light. The function of the button is to | ||||||||
| momentarily open the thermostat circuit, which restarts the | |||||||||
| cleaning | |||||||||
| system. |
|
| |||||||
| cleaning when you pull out the rod. Be sure that the floor |
|
| |||||||
| 15. Thermocouple |
|
| |||||||
| returns to a completely closed position or your appliance will |
|
| |||||||
| not operate properly. |
|
|
|
| The thermocouple is located on top of the firepot inside | ||||
| 6. Fuse |
|
|
|
| the thermocouple cover (ceramic protection tube). The | ||||
| The fuse is located on the front of the junction box on the | thermocouple sends a millivolt signal to the control box | ||||||||
| indicating the preset temperatures of the green and red lights | |||||||||
| right side of the appliance. The fuse will blow should a short | |||||||||
| have been obtained. |
|
| |||||||
| occur and shut off power to the appliance. |
|
|
|
| |||||
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| |
Page 36 |
|
| December 16, 2011 |