2

R

CB 1200 Pellet Stove

 

 

 

 

 

 

 

Getting Started

 

A.Design, Installation & Location Consider- ations

1.Appliance Location

NOTICE: Check building codes prior to installation.

Installation MUST comply with local, regional, state and national codes and regulations.

Consult insurance carrier, local building inspector, fire officials or authorities having jurisdiction over restrictions, installation inspection and permits.

It is a good idea to plan your installation on paper, using exact measurements for clearances and floor protection, before actually beginning the installation

Consideration must be given to:

Safety, convenience, traffic flow

Placement of the chimney and chimney connector.

If you are not using an existing chimney, place the appli- ance where there will be a clear passage for a factory- built listed chimney through the ceiling and roof.

Installing an optional outside air kit would affect the loca- tion of the vent termination.

Since pellet exhaust can contain ash, soot or sparks, you must consider the location of:

Windows

Air Intakes

Air Conditioner

Overhang, soffits, porch roofs, adjacent walls

Landscaping, vegetation

When locating vent and venting termination, vent above roof line when possible.

Warning! Risk of Fire Damaged parts could impair safe operation. Do NOT install damaged, incomplete or substitute components.

CAUTION! If burning shelled field corn, you must use ap- proved venting specifically designed for corn to prevent corro- sion or degradation. Follow the instructions from the venting manufacturer.

NOTICE: Locating the appliance in a location of considerable air movement can cause intermittent smoke spillage from appliance. Do not locate appliance near:

Frequently open doors

Central heat outlets or returns

 

Recommended Location:

Recommended Location:

Above peak

• Above peak

Inside heated space

Location NOT recommended:

Not the highest point of the roof

Wind loading possible

Windward

Marginal Location:

• Below peak

Recommended:

Insulated exterior chase in cooler climates

Marginal Location:

• Wind loading possible

Location NOT recommended:

• Too close to tree

• Below adjacent structure

• Lower roof line

• Avoid outside wall

Leeward

Recommended: Outside Air Intake on windward side

Multi-level Roofs

NOT recommended: Outside Air Intake on leeward side

Figure 5.1

December 16, 2011

7014-179D

Page 5

Page 5
Image 5
Quadra-Fire CB1200M-MBK owner manual Getting Started, Design, Installation & Location Consider- ations, Appliance Location

CB1200M-MBK specifications

The Quadra-Fire CB1200M-MBK is a remarkable addition to the lineup of high-efficiency wood stoves, designed to provide exceptional heating performance while maintaining a user-friendly interface and aesthetic appeal. Known for its sleek design and modern technology, the CB1200M-MBK stands out as a powerful solution for both environmentally conscious homeowners and those in search of reliable warmth during cold months.

One of the main features of the CB1200M-MBK is its high efficiency rating, often exceeding 75%. This impressive figure is attributed to its innovative combustion technology, which maximizes wood-burning efficiency by promoting complete combustion. This means more heat is generated from less wood, translating to reduced emissions and less frequent refueling. This efficient design not only benefits the environment but also provides a cost-effective heating solution.

The CB1200M-MBK is equipped with a large firebox that can accommodate logs up to 18 inches long, allowing users to enjoy extended burn times and consistent heat output. With a capacity of up to 70,000 BTUs, this stove can efficiently heat spaces ranging from 1,000 to 2,200 square feet, making it suitable for a variety of home sizes.

Another standout feature is its advanced air control system, which provides precise control over combustion levels. This system enables users to adjust the air intake to optimize the fire's intensity, ensuring both comfort and efficiency. Additionally, the stove comes with a built-in ash pan, making cleanup easier and enhancing the overall user experience.

The CB1200M-MBK also showcases an appealing aesthetic, featuring a clean, modern design with a traditional cast-iron appearance. The durable, black finish offers an elegant touch, making it a stylish focal point in any room. Moreover, this model is designed to be compatible with various installation options, including top or rear venting, providing flexibility depending on the specific needs of the home.

Durability is another hallmark of the CB1200M-MBK, constructed with high-quality materials that ensure longevity and performance. The heavy-duty steel construction and quality ceramic glass withstand high temperatures and resist cracking, promising years of reliable use.

In conclusion, the Quadra-Fire CB1200M-MBK is a perfect blend of efficiency, performance, and style. With its impressive BTU output, advanced combustion technology, and user-friendly design, it stands as an ideal choice for homeowners looking to enhance their heating solutions while being mindful of environmental impacts.