Manuals / Quadra-Fire / Household Appliance / Indoor Fireplace

Quadra-Fire QV36DC-A VENTING WITH THREE 3 90 ELBOWS, V Ft, H + H1, Venting with three 90 elbows

Models: QV36DC-A

1 36

Page 17

VENTING WITH THREE (3) 90° ELBOWS
	H1
		V1
		V
		H
V (FT.)		H (FT.)
1’ MIN. (305mm)		5’ MAX. (1.52m)
2’ MIN. (610mm)		10’ MAX. (3.1m)
3’ MIN. (914mm)		15’ MAX. (4.65m)
4’ MIN. (1.22m)		20’ MAX. (6.2m)
NOTE: H + H1 = 20’ MAX. (6.2m)
	V + V1 + H + H1= 40’ MAX. (12.4m)
V1
	H1	V
		V
		H
V (FT.)	H + H1	(FT.)
1’ MIN. (305mm)	5’ MAX. (1.52m)
2’ MIN. (610mm)	10’ MAX. (3.1m)
3’ MIN. (914mm)	15’ MAX. (4.65m)
4’ MIN. (1.22m)	20’ MAX. (6.2m)
H +H1 = 20’ MAX. (6.2m)
NOTE: V+V1+H +H1 = 40’ MAX. (12.4m)
Figure 16. Venting with three 90° elbows
20	Quadra-Fire • QV36DC-A • 2161-900 Rev. C • 6/09

Page 17

Image 17

Quadra-Fire QV36DC-A owner manual VENTING WITH THREE 3 90 ELBOWS, V Ft, H + H1, Venting with three 90 elbows

Contents

What to do if you smell gas QV36DC-AModel PROHIBITED SAFETY AND WARNING INFORMATIONTABLE OF CONTENTS High Altitude Installations Installation Codes1Approvals and Codes Appliance CertiﬁcationInstallation of Carbon Monoxide Detectors 2Getting Started Pre-installationPreparationIntroducing Quadra-FireGas Fireplaces ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARDACCESS Figure 1. Diagram of the QV36DC-AACCESS STANDOFFSConstructing the Fireplace Chase 3Installing the FireplaceStep 1. Locating the Fireplace Fireplace Dimensions, LocationsStep 2. Framing the Fireplace 12 DVP12 14-1/4 NOTE PIPES OVERLAP 1-1/4INCHES AT EACH JOINTDVP12A 9-7/8 45.0 10-1/4DVP45 8-9/16 12-9/16 DVP90STIdentifying Vent Components Step 3. Installing the Vent SystemA. Vent System Approvals TEMS OR COMPONENTS MAY BE USEDADJUSTABLE FLUE Flue Restrictor InstructionsSTRAIGHT UP VERTICAL VENTING V FT 40’ MAX. 12.4 MFigure 10. Corner Installation Figure 9. Horizontal Installation90-DEGREEELBOWS 45-DEGREEELBOWFigure 11. Venting with One 90 Elbow VENTING WITH ONE 1 90 ELBOWVENTING WITH ONE 1 90 ELBOW Figure 12. Venting with One 90 Elbow90 ELBOWS VENTING WITH TWOVENTING WITH TWO 2 90o ELBOWS Figure 13. Venting with Two 90 ElbowsFigure 15. Venting with three 90 elbows VENTING WITH THREE 3 90 ELBOWSH + H1 H + H1 + H2V FT VENTING WITH THREE 3 90 ELBOWSH + H1 Figure 16. Venting with three 90 elbowsDVP PIPE B. Installing Vent ComponentsVenting Out the Rear Vent Venting Out the Top VentFigure 22. Adding Venting Components To Install the Heat Shield4. Install Support Brackets 5. Install Firestops Figure 25. 10” x 10” Hole & New Framing Members C. Vent Termination1 inch 25mm Attic FirestopAlcove Applications = AREA WHERE TERMINAL IS NOT PERMITTED= VENT TERMINAL X = AIR SUPPLY INLETMark the roof hole accordingly Figure 31. Proper Positioning, Leveling, and Step 5. The Gas Control SystemSecuring of a Fireplace WARNING THIS UNIT IS NOT FOR USE WITH SOLID FUELStep 7. Gas Pressure Requirements Step 6. The Gas Supply LinePressure Natural GasStep Wiring the FireplaceOptional Accessories Wall SwitchHearth Extensions Step 9. Finishingand Ember Material Step 10. Installing Trim, Refractory, LogsInstalling the Trim Refractory Kit Placement BRICK-292Step 12. Lighting the Appliance Step 11. Before Lighting the FireplaceShutter Settings Review safety warnings and cautionsLIGHTING INSTRUCTIONS FOR YOUR SAFETY READ BEFORE LIGHTINGTO TURN OFF GAS TO APPLIANCE WARNING CAUTIONFireplace Maintenance After the Installation4Maintaining and Servicing Your Fireplace Step 13 Climate ControlStanding Pilot Ignition System TroubleshootingSymptom Possible CausesSymptom Troubleshooting continuedPossible Cause Corrective ActionQuadra-Fire QV36DC-A 2161-900Rev. C 6/09 ÎLimited Lifetime WarrantyQuadra-Fire QV36DC-A 2161-900Rev. C 6/09 ÎLimited Lifetime WarrantyDO NOT DISCARD THIS MANUAL Contact Information

V (FT.)

H + H1

Figure 16. Venting with three 90° elbows