Manuals / Quadra-Fire / Household Appliance / Indoor Fireplace

Quadra-Fire Diagram of the QV36DC-A, Standoffs, Hood, Rating, Plate And, Labels, Electrical

Models: QV36DC-A

1 36

Page 7

		28 1/2 [724mm]
14 1/4
[362mm]
			21 1/2 [548mm]
8 5/8 [219mm]		11 5/8 [297mm]
VENT COLLARS		11 5/8 [297mm]	ELECTRICAL	8 5/8
VENT COLLARS				8 5/8
				[219mm]
			ACCESS	[219mm]
			ACCESS	VENT
				COLLARS
GAS LINE
ACCESS
38		25 1/4	34 5/8
[965mm]		25 1/4	[879mm]
[965mm]		[642mm]	[879mm]
		[642mm]
2 1/8			3 1/2	26 7/8
[55mm]			[90mm]	[682mm]
		36 1/8
		[916mm]
				12 3/4
6 7/8 [174mm]	41 1/8			[323mm]
	[1044mm]
		TOP
		STANDOFFS
		HOOD
	RATING
	PLATE AND
	LABELS
GAS		ELECTRICAL
LINE		ACCESS
ACCESS	GAS
	CONTROLS
Figure 1. Diagram of the QV36DC-A
10	Quadra-Fire • QV36DC-A • 2161-900 Rev. C • 6/09

Page 7

Image 7

Quadra-Fire Diagram of the QV36DC-A, Standoffs, Hood, Rating, Plate And, Labels, Electrical, Line, Access, Controls

Contents

Model QV36DC-AWhat to do if you smell gas PROHIBITED SAFETY AND WARNING INFORMATIONTABLE OF CONTENTS Appliance Certiﬁcation Installation CodesHigh Altitude Installations 1Approvals and CodesInstallation of Carbon Monoxide Detectors ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARD Pre-installationPreparation2Getting Started Introducing Quadra-FireGas FireplacesSTANDOFFS Figure 1. Diagram of the QV36DC-AACCESS ACCESSFireplace Dimensions, Locations 3Installing the FireplaceConstructing the Fireplace Chase Step 1. Locating the FireplaceStep 2. Framing the Fireplace DVP90ST NOTE PIPES OVERLAP 1-1/4INCHES AT EACH JOINT12 DVP12 14-1/4 DVP12A 9-7/8 45.0 10-1/4DVP45 8-9/16 12-9/16TEMS OR COMPONENTS MAY BE USED Step 3. Installing the Vent SystemIdentifying Vent Components A. Vent System ApprovalsVERTICAL VENTING V FT 40’ MAX. 12.4 M Flue Restrictor InstructionsADJUSTABLE FLUE STRAIGHT UP45-DEGREEELBOW Figure 9. Horizontal InstallationFigure 10. Corner Installation 90-DEGREEELBOWSFigure 12. Venting with One 90 Elbow VENTING WITH ONE 1 90 ELBOWFigure 11. Venting with One 90 Elbow VENTING WITH ONE 1 90 ELBOWFigure 13. Venting with Two 90 Elbows VENTING WITH TWO90 ELBOWS VENTING WITH TWO 2 90o ELBOWSH + H1 + H2 VENTING WITH THREE 3 90 ELBOWSFigure 15. Venting with three 90 elbows H + H1Figure 16. Venting with three 90 elbows VENTING WITH THREE 3 90 ELBOWSV FT H + H1Venting Out the Top Vent B. Installing Vent ComponentsDVP PIPE Venting Out the Rear Vent4. Install Support Brackets To Install the Heat ShieldFigure 22. Adding Venting Components 5. Install Firestops Attic Firestop C. Vent TerminationFigure 25. 10” x 10” Hole & New Framing Members 1 inch 25mmX = AIR SUPPLY INLET = AREA WHERE TERMINAL IS NOT PERMITTEDAlcove Applications = VENT TERMINALMark the roof hole accordingly WARNING THIS UNIT IS NOT FOR USE WITH SOLID FUEL Step 5. The Gas Control SystemFigure 31. Proper Positioning, Leveling, and Securing of a FireplaceNatural Gas Step 6. The Gas Supply LineStep 7. Gas Pressure Requirements PressureWall Switch Wiring the FireplaceStep Optional AccessoriesHearth Extensions Step 9. FinishingRefractory Kit Placement BRICK-292 Step 10. Installing Trim, Refractory, Logsand Ember Material Installing the TrimReview safety warnings and cautions Step 11. Before Lighting the FireplaceStep 12. Lighting the Appliance Shutter SettingsWARNING CAUTION FOR YOUR SAFETY READ BEFORE LIGHTINGLIGHTING INSTRUCTIONS TO TURN OFF GAS TO APPLIANCEStep 13 Climate Control After the InstallationFireplace Maintenance 4Maintaining and Servicing Your FireplacePossible Causes TroubleshootingStanding Pilot Ignition System SymptomCorrective Action Troubleshooting continuedSymptom Possible CauseQuadra-Fire QV36DC-A 2161-900Rev. C 6/09 ÎLimited Lifetime WarrantyQuadra-Fire QV36DC-A 2161-900Rev. C 6/09 ÎLimited Lifetime WarrantyDO NOT DISCARD THIS MANUAL Contact Information

STANDOFFS

HOOD

RATING

PLATE AND

LABELS

ELECTRICAL

LINE

ACCESS

CONTROLS

Figure 1. Diagram of the QV36DC-A