A.5 |
|
| With proper installation, operation, and maintenance your gas fireplace will | |||
|
|
|
| provide years of | ||
|
|
|
| troubleshooting guide will assist a qualified service person in the diagnosis | ||
|
|
|
| of a problem and the corrective action to be taken. This troubleshooting | ||
|
| Troubleshooting | guide can only be used by a qualified service technician. | |||
|
|
|
|
| ||
|
|
|
| |||
|
|
|
|
| ||
Standing Pilot Ignition System |
|
|
| |||
|
|
|
|
|
| |
Symptom |
| Possible Causes | Corrective Action |
| ||
|
|
|
|
|
| |
1. After repeated triggering | a. Defective ignitor. |
| Check the spark at the electrode and pilot. If no spark and electrode |
| ||
of the red or black piezo |
|
| wire is properly connected, replace the ignitor. |
| ||
ignitor button, the spark |
|
|
|
| ||
b. Defective pilot or misaligned | Using match, light the pilot. If the pilot lights, turn off the pilot and |
| ||||
ignitor will not light the pilot. |
| |||||
|
|
| electrode (spark at electrode). | trigger the red piezo ignitor button again. If the pilot lights, an im- |
| |
|
|
|
|
| proper gas/air mixture caused the bad lighting and a longer purge |
|
|
|
|
|
| period is recommended. If the pilot will not light, ensure the gap |
|
|
|
|
|
| at the electrode and pilot is |
|
|
|
|
|
| spark. If the gap is OK, replace the pilot. |
|
|
|
|
|
|
| |
|
|
| c. No gas or low gas pressure. | Check the remote |
| |
|
|
|
|
| is a valve near the gas main. There can be more than one (1) valve |
|
|
|
|
|
| between the fireplace and the main. |
|
|
|
|
|
|
|
|
|
|
| d. No LP in tank. |
| Check the LP (propane) tank. You may be out of fuel. |
|
|
|
|
|
| ||
2. The pilot will not stay lit | a. Defective thermocouple. | Check that the pilot flame impinges on the thermocouple. Clean |
| |||
after carefully following the |
|
| and/or adjust the pilot for maximum flame impingement. |
| ||
lighting instructions. |
|
|
| Ensure that the thermocouple connection at the gas valve is fully |
| |
|
|
|
|
|
| |
|
|
|
|
| inserted and tight (hand tighten plus 1/4 turn). |
|
|
|
|
|
| Disconnect the thermocouple from the valve, place one millivolt |
|
|
|
|
|
| meter lead wire on the tip of the thermcouple and the other meter |
|
|
|
|
|
| lead wire on the thermocouple copper lead. Start the pilot and hold |
|
|
|
|
|
| the valve knob in. If the millivolt reading is less than 15mV, replace |
|
|
|
|
|
| the thermocouple. |
|
|
|
|
|
|
|
|
|
|
| b. Defective valve. |
| If the thermocouple is producing more than 15 millivolts, replace |
|
|
|
|
|
| faulty valve. |
|
|
|
|
|
| ||
3. The pilot is burning, | a. ON/OFF switch or wires | Check the ON/OFF switch and wires for proper connections. Place |
| |||
there is no burner flame, | defective. |
| the jumper wires across the terminals at the switch. If the burner |
| ||
the valve knob is in the ON |
|
| comes on, replace the defective switch. If the switch is OK, place the |
| ||
position, and the ON/OFF |
|
| jumper wires across the switch wires at the gas valve. If the burner |
| ||
switch is in the ON position. |
|
| comes on, the wires are faulty or connections are bad. |
| ||
|
|
|
|
|
| |
|
|
| b. Thermopile may not be gener- | If the pilot flame is not close enough physically to the thermopile, |
| |
|
|
| ating sufficient millivoltage. | adjust the pilot flame. |
| |
|
|
|
|
| Be sure the wire connections from the thermopile at the gas valve |
|
|
|
|
|
| terminals are tight and that the thermopile is fully inserted into the |
|
|
|
|
|
| pilot bracket. |
|
|
|
|
|
| Check the thermopile with a millivolt meter. Take the reading at |
|
|
|
|
|
|
| |
|
|
|
|
| millivolts minimum, while holding the valve knob depressed in the |
|
|
|
|
|
| pilot position, with the pilot lit, and the ON/OFF switch in the OFF |
|
|
|
|
|
| position. Replace the faulty thermopile if the reading is below the |
|
|
|
|
|
| specified minimum. |
|
|
|
|
|
| With the pilot in the ON position, disconnect the thermopile leads |
|
|
|
|
|
| from the valve. Take a reading at the thermopile leads. The read- |
|
|
|
|
|
| ing should be 325 millivolts minimum. Replace the thermopile if the |
|
|
|
|
|
| reading is below the minimum. |
|
|
|
|
|
|
|
|
35 |