INSTALLATION
IMPORTANT:
SAVE THESE
INSTRUCTIONS
The FPI Gas Fireplace must be installed in accordance with these instructions. Carefully read all the instructions in this manual fi rst. Consult the building authority having jurisdic- tion to determine the need for a permit prior to starting the installation.
NOTE: Failure to follow the instructions could cause a malfunction of the heater which could result in death, serious bodily injury, and/or property damage. Failure to follow these instructions may also void your fi re insurance and/or warranty.
FOR YOUR SAFETY
This appliance requires air for proper combus- tion. Always provide adequate combustion and ventilation air. Follow instructions and informa- tion in CSA B149.1 (in Canada) or the National Fuel Gas CodeANS Z223.1/NFPA(in the USA), regarding requirements for combustion and ventilation air.
GAS PRESSURE
TESTING
The appliance must be isolated from the gas supply piping system by closing its individual manual shut off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than
1/2 psig. (3.45 kPa).
SPECIFICATIONS
At pressures over 1/2 psig, the pipe to the unit must be disconnected.
Gas Input Capacity:
Natural Gas 38,000 Btu/h
Propane | 35,500 Btu/h |
Min. Input:
Natural Gas 20,000 Btu/h
Propane | 19,000 Btu/h |
Fuels: Approved for use with both natural gas, and propane. Approved as is for use at 0' to 4,500'
Electrical: 120V A.C. system.
Circulation Fan: Variable speed, 127 CFM.
Log Set: Ceramic fi bre, 8 per set.
Vent System: 3"
INSTALLATION INTO A SOLID FUEL BURNING FIREPLACE OR FACTORY BUILT FIREPLACE
The E33 Gas Inserts have been tested and ap- proved to be vented into any masonry fi replace or approved solid fuel burning factory built
fireplace that will allow the insert to physically
fit into the fi rebox. Refer to page 6 for minimum
fireplace clearances.
If the factory built fireplace* height is too low for your Insert, you may remove the smoke baffle plate and damper from the factory built fireplace as long as these items are saved and are reinstalled in the event that the Insert is removed. NOTE:Any alterations made to the listed solid fuel burning factory built fireplace may void the listing of the fireplace. Cutting any
If the
The fireplace and fireplace chimney must be clean and in good working order and con- structed of
*Check with your local inspector before com- mencing with this installation.
BEFORE YOU START
Safe installation and operation of this appliance requires common sense, however, we are required by the Canadian Safety Standards and ANSI Standards to make you aware of the following:
General Safety Information
1)The appliance installation must conform with local codes or in the absence of local codes, with CAN/CSA B149.1 (in Canada) or the National Fuel Gas CodeANSI Z223.1 NFPA54 in the U.S.A.This appliance should beinstalledbyaqualifiedgasfittertechnician only.
2)Installation and repair should be done by a qualified service person.
3)The appliance should be inspected before use and at least annually by a professional service person. More fre- quent cleaning may be required due to excessive lint from carpeting, bedding material, animal hair, etc. It is impera- tive that control compartments, burners and circulating air passageways of the appliance be kept clean.
4)See general construction and assembly instructions. This appliance may only be installed in a vented, noncombustible fi re- place.
5)This appliance is Listed for bedroom instal- lations when used with a Listed Millivolt Thermostat. Some areas may have further requirements, check local codes before installation.
6)Always connect this appliance to a vent system vent that is run (or routed) to the outside of the building envelope. Never vent to another room or inside a building. Make sure that the vent is properly sized and is of adequate height to provide the proper draft.
7)Inspect the venting system annually for blockage and any signs of deterioration.
8)Any glass removed for servicing must be replaced prior to operating the appliance.
9)WARNING: Failure to position the parts in accordance with the diagrams in this manualorfailuretouseonlypartsspecifi- cally approved with this appliance may result in property damage or personal injury.
10)To prevent injury, do not allow anyone who is unfamiliar with the operation to use the fi replace.
E33 FPI Direct Vent Gas Insert | 5 |
|