Manuals / Regency / Household Appliance / Indoor Fireplace

Regency P33-LP4 installation manual P33-4Zero Clearance, Direct Vent Gas Fireplace, Owners

Models: P33-LP4

1 52

Download 52 pages 40.32 Kb

Page 1

P33-4 Zero Clearance

www.regency-ﬁre.com

P33-4 Zero Clearance	Owners &
Direct Vent Gas Fireplace	Installation Manual

MODELS: P33-NG4 Natural Gas P33-LP4 Propane

WARNING:

Iftheinformationintheseinstructionsarenotfollowedexactly, a ﬁre or explosion may result causing property damage, personal injury or loss of life.

FOR YOUR SAFETY

Do not store or use gasoline or other ﬂammable vapors and liquids in the vicinity of this or any other appliance.

Installation and service must be performed by a qualiﬁed installer, service agency or the gas supplier.

FOR YOUR SAFETY

What to do if you smell gas:

Do not try to light any appliance

Do not touch any electrical switch: do not use any phone in your building.

Immediately call your gas supplier from a neighbour's phone. Follow the gas supplier's instructions.

If you cannot reach your gas supplier, call the ﬁre department.

Tested by:

Installer: Please complete the details on the back cover

and leave this manual with the homeowner.

Homeowner: Please keep these instructions for future reference.

918-520a

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4

03/05/08

Image 1

Regency P33-LP4 installation manual P33-4Zero Clearance, Direct Vent Gas Fireplace, Owners, Installation Manual

Contents

P33-4Zero Clearance Installation ManualDirect Vent Gas Fireplace OwnersTo the New Owner MAINTENANCE TABLE OF CONTENTSPARTS LIST WARRANTYSAFETY LABEL SAFETY LABELMA Code - CO Detector REQUIREMENTS5.08 Modifications to NFPA-54,Chapter OBSTRUCTIONSGENERAL SAFETY INFORMATION INSTALLATIONIMPORTANT MESSAGE BEFORE YOU STARTINSTALLATION CHECKLIST INSTALLATIONUNIT DIMENSIONS Vent Termination Locations Section DiagramCLEARANCES INSTALLATIONMANTEL LEG CLEARANCES COMBUSTIBLE MANTELSFRAMING AND FINISHING INSTALLATIONRigid Vent Minimum ClearancesUNIT ASSEMBLY PRIOR TO INSTALLATION INSTALLATIONTop Standoff Assembly VENTING INTRODUCTIONEXTERIOR VENT TERMINATION LOCATIONS INSTALLATIONREGENCY DIRECT VENT FLEX SYSTEM INSTALLATIONMINIMUM RIGID PIPE CENTER-LINE MINIMUM FLEX KIT CENTER-LINEINSTALLATION PROCEDURES INSTALLATIONRIGID PIPE VENTING SYSTEMS INSTALLATIONAlternate Caps4” X 6-5/8”RIGID PIPE CROSS REFERENCE CHART INSTALLATION4” x 6-5/8”Rigid Pipe Cross Reference Chart Cont INSTALLATIONOffset Pipe Selection RIGID PIPE VENTING ARRANGEMENTS INSTALLATIONVertical Terminations Propane & Natural Gas Vent must be supported at offsetsThe P33-4is approved for a maximum 40 ft. straight vertical, with rigid pipe vent systems for Propane and Natural Gas INSTALLATIONVent must be supported at offsets Maintain clearances to combustiblesRIGID PIPE VENTING ARRANGEMENTS INSTALLATIONREGENCY DIRECT VENT SYSTEM FLEX Minimum Simpson Dura-Vent Center-LineHorizontal Venting with Two 2 90o Elbows INSTALLATIONHorizontal Venting with Three 3 90o Elbows Horizontal Venting with Two 2 90o ElbowsHorizontal Venting with Three 3 90o Elbows INSTALLATIONVertical Venting with Two 2 90o Elbows Vertical Venting with Two 2 90o ElbowsVertical Venting with Three 3 90o Elbows INSTALLATIONVertical Venting with Three 3 90o Elbows OptionVERTICAL TERMINATION WITH CO-LINEARFLEX SYSTEM INSTALLATIONCo-linearDV Vertical Termination Cap # Amaximum of two certified joiner kitsThe shaded area in the diagrams show INSTALLATIONVENTING ARRANGEMENTS - VERTICAL TERMINATIONS VerticalHeightfeetUNIT INSTALLATION WITH HORIZONTAL TERMINATION INSTALLATIONDiagram DiagramUNIT INSTALLATION WITH VERTICAL TERMINATION INSTALLATIONGAS LINE INSTALLATION DiagramPILOT ADJUSTMENT INSTALLATIONGAS PIPE PRESSURE TESTING HIGH ELEVATIONFor P33-4/H25-1Using SIT 820 NOVA Gas Valve INSTALLATIONInstallation of the LPG Conversion Kit Assembly to the left and lift outDo not overtighten the screw. Recommended to grip INSTALLATIONthe wrench by the short side Also check that the pilot andIgnitor Wire Piezo Ignitor INSTALLATIONGround wire from kit Battery CompartmentLOG SET INSTALLATION INSTALLATIONOPTIONAL BRICK PANELSDiagram Diagram INSTALLATIONDiagram STANDARD FLUSH DOORDiagram INSTALLATIONClip locations Clip installed on right side FLUSH LOUVERSBAY LOUVERS INSTALLATIONFlush Louver Top Heat Shield Bay Louver Top Heat ShieldFULL SCREEN DOORS INSTALLATIONBackside of FullFlange Screen Door Frame Shown Cut-Out Oblong Hole Cut-Out Top Flange BottomHinge Location Bottom Grill INSTALLATIONHinge Left Side of Bottom Grill Screen DoorOptional REMOTE CONTROL INSTALLATIONOptional WALL SWITCH Do not wire millivolt wall switch wireWIRING DIAGRAMS INSTALLATIONINSTALLATION INSTALLING THE OPTIONAL FAN INSTALLATION1 Shut the power off DiagramCOPY OF THE LIGHTING PLATE INSTRUCTIONS OPERATING INSTRUCTIONSGas Inlet SHUTDOWN PROCEDURE LIGHTING PROCEDUREAERATION ADJUSTMENT CLEAN THE GLASS WHILE IT IS HOTMAINTENANCE MAINTENANCELOG REPLACEMENT MAINTENANCEFlush Glass Replacement MAINTENANCEBay Glass Replacement THERMOPILE THERMOCOUPLEINSTALLING VALVE MAINTENANCEDiagram 3 Lift out Valve Tray Assembly Diagram 2 Rear Log Stand & Valve Tray AssemblyMAIN ASSEMBLY PARTS LISTPARTS LIST BURNER & LOG ASSEMBLY PARTS LISTPart Description FLUSH FRONT & LOUVERS PARTS LISTBAY FRONT & LOUVERS PARTS LISTConditions WARRANTYExclusions thoroughly before it leaves our door