Manuals / Regency / Household Appliance / Indoor Fireplace

Regency P33-LP4 Installation, Venting Arrangements - Vertical Terminations, VerticalHeightfeet

Models: P33-LP4

1 52

Download 52 pages 40.32 Kb

Page 24

Image 24

INSTALLATION

VENTING ARRANGEMENTS - VERTICAL TERMINATIONS

with Co-linear Flex System for both Residential & Manufactured Homes into Masonry Fireplaces

	30
VerticalHeight(feet)	(51mm)max.	8'(2.4m)Min.	30'(9.1m)Max.
	2’
		30”	(762mm)

Horizontal Distance (Feet)

The shaded area in the diagrams show

the allowable vertical terminations.

24	Regency® P33-4 Zero Clearance Direct Vent Gas Fireplace

Page 24

Image 24

Regency P33-LP4 Installation, Venting Arrangements - Vertical Terminations, VerticalHeightfeet, Horizontal Distance Feet

Contents

Installation Manual P33-4Zero ClearanceDirect Vent Gas Fireplace OwnersTo the New Owner TABLE OF CONTENTS MAINTENANCEPARTS LIST WARRANTYSAFETY LABEL SAFETY LABELREQUIREMENTS MA Code - CO Detector5.08 Modifications to NFPA-54,Chapter OBSTRUCTIONSINSTALLATION GENERAL SAFETY INFORMATIONIMPORTANT MESSAGE BEFORE YOU STARTINSTALLATION INSTALLATION CHECKLISTUNIT DIMENSIONS Vent Termination Locations Section DiagramINSTALLATION CLEARANCESMANTEL LEG CLEARANCES COMBUSTIBLE MANTELSINSTALLATION FRAMING AND FINISHINGRigid Vent Minimum ClearancesINSTALLATION UNIT ASSEMBLY PRIOR TO INSTALLATIONTop Standoff Assembly VENTING INTRODUCTIONINSTALLATION EXTERIOR VENT TERMINATION LOCATIONSINSTALLATION REGENCY DIRECT VENT FLEX SYSTEMMINIMUM RIGID PIPE CENTER-LINE MINIMUM FLEX KIT CENTER-LINEINSTALLATION INSTALLATION PROCEDURESINSTALLATION RIGID PIPE VENTING SYSTEMSAlternate CapsINSTALLATION 4” X 6-5/8”RIGID PIPE CROSS REFERENCE CHARTINSTALLATION 4” x 6-5/8”Rigid Pipe Cross Reference Chart ContOffset Pipe Selection INSTALLATION RIGID PIPE VENTING ARRANGEMENTSVertical Terminations Propane & Natural Gas Vent must be supported at offsetsINSTALLATION The P33-4is approved for a maximum 40 ft. straight vertical, with rigid pipe vent systems for Propane and Natural GasVent must be supported at offsets Maintain clearances to combustiblesINSTALLATION RIGID PIPE VENTING ARRANGEMENTSREGENCY DIRECT VENT SYSTEM FLEX Minimum Simpson Dura-Vent Center-LineINSTALLATION Horizontal Venting with Two 2 90o ElbowsHorizontal Venting with Three 3 90o Elbows Horizontal Venting with Two 2 90o ElbowsINSTALLATION Horizontal Venting with Three 3 90o ElbowsVertical Venting with Two 2 90o Elbows Vertical Venting with Two 2 90o ElbowsINSTALLATION Vertical Venting with Three 3 90o ElbowsVertical Venting with Three 3 90o Elbows OptionINSTALLATION VERTICAL TERMINATION WITH CO-LINEARFLEX SYSTEMCo-linearDV Vertical Termination Cap # Amaximum of two certified joiner kitsINSTALLATION The shaded area in the diagrams showVENTING ARRANGEMENTS - VERTICAL TERMINATIONS VerticalHeightfeetINSTALLATION UNIT INSTALLATION WITH HORIZONTAL TERMINATIONDiagram DiagramINSTALLATION UNIT INSTALLATION WITH VERTICAL TERMINATIONGAS LINE INSTALLATION DiagramINSTALLATION PILOT ADJUSTMENTGAS PIPE PRESSURE TESTING HIGH ELEVATIONINSTALLATION For P33-4/H25-1Using SIT 820 NOVA Gas ValveInstallation of the LPG Conversion Kit Assembly to the left and lift outINSTALLATION Do not overtighten the screw. Recommended to gripthe wrench by the short side Also check that the pilot andINSTALLATION Ignitor Wire Piezo IgnitorGround wire from kit Battery CompartmentINSTALLATION LOG SET INSTALLATIONOPTIONAL BRICK PANELSINSTALLATION Diagram DiagramDiagram STANDARD FLUSH DOORINSTALLATION DiagramClip locations Clip installed on right side FLUSH LOUVERSINSTALLATION BAY LOUVERSFlush Louver Top Heat Shield Bay Louver Top Heat ShieldINSTALLATION FULL SCREEN DOORSBackside of FullFlange Screen Door Frame Shown Cut-Out Oblong Hole Cut-Out Top Flange BottomINSTALLATION Hinge Location Bottom GrillHinge Left Side of Bottom Grill Screen DoorINSTALLATION Optional REMOTE CONTROLOptional WALL SWITCH Do not wire millivolt wall switch wireINSTALLATION WIRING DIAGRAMSINSTALLATION INSTALLATION INSTALLING THE OPTIONAL FAN1 Shut the power off DiagramOPERATING INSTRUCTIONS COPY OF THE LIGHTING PLATE INSTRUCTIONSGas Inlet LIGHTING PROCEDURE SHUTDOWN PROCEDUREAERATION ADJUSTMENT CLEAN THE GLASS WHILE IT IS HOTMAINTENANCE MAINTENANCELOG REPLACEMENT MAINTENANCEMAINTENANCE Flush Glass ReplacementBay Glass Replacement THERMOPILE THERMOCOUPLEMAINTENANCE INSTALLING VALVEDiagram 3 Lift out Valve Tray Assembly Diagram 2 Rear Log Stand & Valve Tray AssemblyPARTS LIST MAIN ASSEMBLYPARTS LIST PARTS LIST BURNER & LOG ASSEMBLYPart Description PARTS LIST FLUSH FRONT & LOUVERSPARTS LIST BAY FRONT & LOUVERSWARRANTY ConditionsExclusions thoroughly before it leaves our door

VENTING ARRANGEMENTS - VERTICAL TERMINATIONS

VerticalHeight(feet)

(762mm)

Horizontal Distance (Feet)

The shaded area in the diagrams show

the allowable vertical terminations.