Regency P33R-LP2 Pilot Adjustment, High Elevation, Gas Pipe Pressure Testing, P33R-2System Data

INSTALLATION

Important: Always check for gas leaks with a soap and water solution or gas leak detector. Do not use open flame for leak testing.

PILOT ADJUSTMENT

Periodically check the pilot flames. Cor- rect flame pattern has three strong blue flames: 1 flowing around the thermopile, 1 around the thermocouple and 1 flowing across the burner (it does not have to be touching the burner).

Note: If you have an incorrect flame pattern, contact your Regency dealer for further instructions.

Incorrect flame pattern will have small,

probably yellow flames, not coming into proper contact with the rear burner or thermopile or thermocouple.

HIGH ELEVATION

This unit is approved in Canada for altitude 0 to 4500 ft. (CAN1 2.17-M91) with the orifice supplied.

P33R-2 System Data

For 0 to 4500 feet altitude
Burner Inlet Orifice Sizes:
Natural Gas		Propane
Burner	#45	#54
Max. Input Rating
- Natural Gas	21,000 Btu/h
- Propane	21,000 Btu/h
Min. Input Rating
-Natural Gas	10,500 Btu/h
-Propane	10,500 Btu/h
Output Capacity with blower Off
Natural Gas	15,960 Btu/h
Propane	16,170 Btu/h
Output Capacity with blower On
Natural Gas	16,170 Btu/h
Propane	16,380 Btu/h
Minimum Output with blower Off
Natural Gas	7,980	Btu/h
Propane	8,085	Btu/h
Supply Pressure
Natural Gas	min.	5.0"	w.c.
Propane	min.	12.0"	w.c.
Manifold Pressure (High)
Natural Gas	3.8"	+/- 0.2" w.c.
Propane	11"	+/- 0.2" w.c.
Electrical: 120 V	A.C. System.

Circulation Fan: variable speed 130 CFM.

Log Set: Ceramic fibre, 5 per set.

Vent System: Simpson Dura-Vent Direct

Vent System or Regency Direct

Vent System (Flex)

Note: Output capacity:

The efficiency rating of the appli- ance is a product thermal efficien- cy rating determined under con- tinuous operating conditions and was determined independently of any installed system.

Vent height may or may not change your efficiency ratings.

GAS PIPE PRESSURE

TESTING

The appliance must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig. (3.45 kPa). Disconnect piping from valve at pressures over 1/2 psig.

The manifold pressure is controlled by a reg- ulator built into the gas control, and should be checked at the pressure test point.

Note: To properly check gas pressure, both inlet and manifold pressures should be checked using the valve pressure ports on the valve.

1)Make sure the valve is in the "OFF" position.

2)Loosen the "IN" and/or "OUT" pressure tap(s), turning counterclockwise with a 1/ 8" wide flat screwdriver.

3)Attach manometer to "IN" and/or "OUT" pressure tap(s) using a 5/16" ID hose.

4)Light the pilot and turn the valve to "ON" position.

5)The pressure check should be carried out with the unit burning and the setting should be within the limits specified on the safety label.

6)When finished reading manometer, turn off the gas valve, disconnect the hose and tighten the screw (clockwise) with a 1/8" flat screwdriver. Note: Screw should be snug, but do not over tighten.

S.I.T. VALVE DESCRIPTION

1) Gas cock knob

2)Manual high/low adjustment

3)Pilot Adjustment

4) Thermocouple Connection - option

5) Outlet Pressure Tap

6)Inlet Pressure Tap

7) Pilot Outlet

8)Main Gas Outlet

9)Alternative TC Connection Point

20 Regency P33R-2 Zero Clearance Rear Vent Direct Vent Gas Fireplace