Remington EL-8: 107624-01, EL-8: 107624-02, EL-8: 107625-01, EL-8: 107625-02, EL-8: 111174-01

SAW CHAIN TENSION ADJUSTMENT

Continued

2.On Model 107624-01, -02, turn adjusting screw clockwise until slack is out of chain. On Model 107625-01, -02, 111174-01 turn thumb knob clock- wise until slack is out of chain (see Figure 7).

3.Wearing protective gloves, move chain around guide bar. Chain should move freely. If chain does not move freely, loosen chain by turning adjusting screw counterclockwise.

4.After chain tension is correct, tighten guide bar nuts Þrmly. If not, guide bar will move and loosen chain tension. This will increase the risk of kick- back. This can also damage saw. Note: A new chain will stretch. Check new chain after Þrst few minutes of operation. Allow chain to cool down. Readjust chain tension.

FILLING OIL TANK

1.Remove oil cap.

2.Fill oil tank with SAE #30 motor oil. Note: For temperatures below 30°F, use SAE #10 oil. For temperatures above 75°F, use SAE #40 oil.

3.Replace oil cap at once. Tighten oil cap Þrmly for good seal. This will avoid oil seepage from tank.

4.Wipe off excess oil.

Note: It is normal for oil to seep when saw is not in use. Empty oil tank after each use to prevent seepage.

OPERATING CHAIN SAW

WARNING: Read and understand this ownerÕsmanualbeforeoperatingthissaw. Make certain you read and understand all Important Safety Information, pages 2 through 4. Improper use of this chain saw can cause severe injury or death from Þre, electricalshock,orbodycontactwithmov- ing chain, or falling wood.

EXTENSION CORDS

Use proper extension cords with this saw. Use only extension cords marked for outdoor use. The cord must be marked with sufÞx W or W-A following the cord type designation. Example: SJTW-A or SJTW. Use proper sized cord with this saw. Cord must be heavy enough to carry current needed. An undersized cord will cause voltage drop at saw. Saw will lose power and overheat. Follow cord size requirements listed below.

Cord Length	AWG Cord Size
25 feet	16 AWG
50 feet	16 AWG
100 feet	14 AWG
150 feet	12 AWG

Models EL-8: 107624-01, -02; 107625-01, -02, 111174-01

Keep cord away from cutting area. Make sure cord does not catch on branches or logs during cutting. Inspect cords often. Replace damaged cords.

This chain saw is designed with an extension cord hitch that prevents the extension cord from being pulled loose during use. To use, form a loop with the end of the extension cord, insert loop into slot in rear of handle, and place loop over cord hitch (see Figure 8). Gently pull loop against cord hitch until slack is removed. Plug extension cord into chain saw cord.

OILING CHAIN

Manual Oil System

Always check oil level before using saw. Do not at- tempt to operate the oil system while saw is in op- eration. To oil chain, press squeeze bulb. Oil will feed onto the guide bar and chain. Press squeeze bulb at least once before each cut. Check oil level often by looking at oil sight window (see Figure 9).

Automatic Oil System

Chain saw Model 107625-01, -02, 111174-01 is equipped with an automatic oiling system. It will pro- vide adequate lubrication to the guide bar and saw chain. Check oil level every 15 minutes of cutting time. Oil level can be seen in oil sight window (see Figure 10).

CUTTING WITH THE CHAIN SAW

1.Connect saw to extension cord. Connect exten- sion cord to power supply.

2.Make sure section of log to be cut is not laying on ground. This will keep chain from touching ground as it cuts through log. Touching ground with moving chain will dull chain.

3.Use both hands to grip saw. Always use left hand to grip front handle and right hand to grip rear handle. Use Þrm grip. Thumbs and Þngers must wrap around saw handles (see Figure 11).

4.Make sure your footing is Þrm. Keep feet apart. Divide your weight evenly on both feet.

5.When ready to make a cut, push the lockout button completely forward with the right thumb and squeeze the trigger (see Figure 11). This will turn saw on. Releasing trigger will turn saw off. Make sure saw is running at full speed before starting a cut.

6.When starting a cut, place moving chain against wood. Hold saw Þrmly in place to avoid possible bouncing or skating (sideways movement) of saw.

Continued

107705 17 www.desatech.com