Renesas M3A-HS71, SH7670 1.2.1 Symbols Used

Before Using the SH7670 CPU Board

1.2.1 Symbols Used

Rev. 1.01 May 7, 2008 1-3

REJ11J0015-0101

1

<Caution Indication>

CAUTION

Regarding the reconstruction of this product:

• Do not reconstruct this product. If the product has gotten out of order for reasons of disassembly

or reconstruction, requests for repair may not be accepted.

Regarding the handling of this product:

z Handle this product with caution, not to let it drop or fall down or apply strong mechanical shock.

z Do not touch the communication interface connector pins or other connector pins directly with

your hand. The internal circuit may be broken by static electricity.

z When moving this product to another place of installation, be careful not to apply strong vibration

or mechanical shock to it.

z After connecting each piece of equipment with cable, check the cables again to see that they are

connected correctly. For details on how to connect, refer to Chapter 2, “Setting Up the Hardware.”

z Before turning on the power for each connected piece of equipment, make sure you’ve finished

connecting all cables. Do not connect or disconnect any cable when the power is turned on.

Regarding the operating procedure for this product:

Note • Exceptional conditions or precautions are noted in an operation procedure or explanatory

description when it is necessary to call the user’s attention.

1.2.1 Symbols Used

Table 1.2.1 lists the symbols used in this manual.

Table 1.2.1 Symbol List

Symbol Meaning

[Menu->Menu Option] The arrow “Æ” indicates a menu option.

Example: File menuÆSave As…

“File name”

“Directory”

“Button"

" … " indicates file names, directory, or button of dialog box.

Example :"C:¥Workspace¥Sample_softwawe¥ SH7670_sample "

"OK" button

"resetprg.c"

Contents

Main REJ11J0015-0101 Rev. 1.01 Issued: May 7. 2008 Renesas 32-Bit RISC Microcomputers SuperHTM RISC engine Family/SH7670 Series M3A-HS71 Installation Manual SH7670 CPU Board Page Page Page [Indication of Warnings and Cautions] Page Important About this product: Purpose of use of this product: For those who use this product: When using this product: Page Usage restrictions: About product changes: About the rights: About diagrams: Page Table of Contents CHAPTER5 CREATING AND RUNNING A NEW PROJECT WORKSPACE ..................................... 5-1 Page Page Page Page Before Using the SH7670 CPU Board 1.1 Overview To Ensure Safe and Correct Use These pictorial indications are explained in the section 1.2, Usage Precautions. Please be sure 1.2 Usage Precautions Do not let foreign matters such as water, pieces of metal or inflammable material get into the The upper-limit ambient temperature at which this product can be used (i.e., rated maximum 1.2.1 Symbols Used Before Using the SH7670 CPU Board 1.3 Procedure for Introducing This Product 1.4 Operating Guarantee for This Product Before Using the SH7670 CPU Board 1.5 Items to Be Prepared by User 1.5.1 Recommended Host Computer Environment Page Page Setting Up the Hardware 2.1 Connections Between SH7670 CPU board and E10A-USB Emulator 2.2 SH7670 CPU board Switch Setting Do not change DIP switch and jumper settings while the SH7670 CPU board is operating. Always 2.2.1 SH7670 CPU board DIP Switch Setting 2.2.2 SH7670 CPU Board Jumper Switch Setting Board edge ON SW8 Setting Up the Hardware 2.3 System Connections and Power-On Sequence Unless the above power-on sequence is followed, unrecoverable damage may occur to the Page Setting Up the Software 3.1 About the HEW 3.1.1 HEW Installation Procedure Page Page Setting Up the Software 3.2 Setting Up the E10A-USB Emulator Software 3.2.1 E10A-USB Software Installation Procedure Page Page Page 3.2.2 Setting Up the E10A-USB Emulator Page Page Do not turn off the power for the host computer or remove the USB cable while the system is Page Page Page Page Page Page Page Running the Software 4.1 Running the Software 4.1.1 Preparing for Downloading the Sample Software 4.1.2 SH7670 CPU board and E10A-USB Startup Procedure (HEW Startup) Page Page Page 4.1.3 E10A-USB Emulator Connection Error Dialog Page 4.1.4 Sample Software Download Procedure Page Page Page Running the Softwareare Page Creating and Running a New Project Workspace 5.1 Creating a New Project Workspace 5.1.1 Preparing for Creating a New Project Workspace 5.1.2 Procedure for Creating a New Project Workspace Page Page Page Page Page Creating and Running a New Project Workspace 5.2 Setting Up the Flash Memory Download 5.2.1 Setting Up the Flash Memory Download Function 5.2.2 Specifying the Command Batch File Before Downloading Creating and Running a New Project Workspace 5.2.3 Activating the Command Line Window 5.3 Adding/Modifying Hardware Setup Files 5.3.1 Copying Hardware Setup Files 5.3.2 Removing the Standard Source Files 5.3.3 Adding Hardware Setup Files File name: Files of type: Look in: 5.3.4 Setting Compiler Options 5.3.5 Setting Linker Options Page Page Page Page Page Page 5.3.6 Writing the Main Function (Operation Confirmation)