Renesas M3A-HS71, SH7670 - page 38

Setting Up the Software

3.2.2 Setting Up the E10A-USB Emulator

Rev. 1.01 May 7, 2008 3-14

REJ11J0015-0101

3

(ii) Setting Up the E10A-USB Emulator Driver

The following shows how to set up the E10A-USB emulator driver.

The setup procedure here is explained for the Windows XP case.

Note: The dialog boxes shown here are displayed when you set up the E10A-USB emulator driver for the first time or

when you’ve changed the USB port on the host computer side and connected the emulator to that port for the first

time. It will take some time until the dialog box appears.

(1) [Found New Hardware Wizard] shown below will start.

In this dialog box, select the option “Install from the list or specific location (Advanced)”, then click “Next”.

Figure3.2.17 New Hardware Detection Wizard Start (1)

(2) Select the option “Search for the best driver in these locations” and select the check box “Search removable media

(floppy, CD-ROM...).” Then click “Next”.

Figure3.2.18 New Hardware Detection Wizard Start (2)

Contents

Main REJ11J0015-0101 Rev. 1.01 Issued: May 7. 2008 Renesas 32-Bit RISC Microcomputers SuperHTM RISC engine Family/SH7670 Series M3A-HS71 Installation Manual SH7670 CPU Board Page Page Page [Indication of Warnings and Cautions] Page Important About this product: Purpose of use of this product: For those who use this product: When using this product: Page Usage restrictions: About product changes: About the rights: About diagrams: Page Table of Contents CHAPTER5 CREATING AND RUNNING A NEW PROJECT WORKSPACE ..................................... 5-1 Page Page Page Page Before Using the SH7670 CPU Board 1.1 Overview To Ensure Safe and Correct Use These pictorial indications are explained in the section 1.2, Usage Precautions. Please be sure 1.2 Usage Precautions Do not let foreign matters such as water, pieces of metal or inflammable material get into the The upper-limit ambient temperature at which this product can be used (i.e., rated maximum 1.2.1 Symbols Used Before Using the SH7670 CPU Board 1.3 Procedure for Introducing This Product 1.4 Operating Guarantee for This Product Before Using the SH7670 CPU Board 1.5 Items to Be Prepared by User 1.5.1 Recommended Host Computer Environment Page Page Setting Up the Hardware 2.1 Connections Between SH7670 CPU board and E10A-USB Emulator 2.2 SH7670 CPU board Switch Setting Do not change DIP switch and jumper settings while the SH7670 CPU board is operating. Always 2.2.1 SH7670 CPU board DIP Switch Setting 2.2.2 SH7670 CPU Board Jumper Switch Setting Board edge ON SW8 Setting Up the Hardware 2.3 System Connections and Power-On Sequence Unless the above power-on sequence is followed, unrecoverable damage may occur to the Page Setting Up the Software 3.1 About the HEW 3.1.1 HEW Installation Procedure Page Page Setting Up the Software 3.2 Setting Up the E10A-USB Emulator Software 3.2.1 E10A-USB Software Installation Procedure Page Page Page 3.2.2 Setting Up the E10A-USB Emulator Page Page Do not turn off the power for the host computer or remove the USB cable while the system is Page Page Page Page Page Page Page Running the Software 4.1 Running the Software 4.1.1 Preparing for Downloading the Sample Software 4.1.2 SH7670 CPU board and E10A-USB Startup Procedure (HEW Startup) Page Page Page 4.1.3 E10A-USB Emulator Connection Error Dialog Page 4.1.4 Sample Software Download Procedure Page Page Page Running the Softwareare Page Creating and Running a New Project Workspace 5.1 Creating a New Project Workspace 5.1.1 Preparing for Creating a New Project Workspace 5.1.2 Procedure for Creating a New Project Workspace Page Page Page Page Page Creating and Running a New Project Workspace 5.2 Setting Up the Flash Memory Download 5.2.1 Setting Up the Flash Memory Download Function 5.2.2 Specifying the Command Batch File Before Downloading Creating and Running a New Project Workspace 5.2.3 Activating the Command Line Window 5.3 Adding/Modifying Hardware Setup Files 5.3.1 Copying Hardware Setup Files 5.3.2 Removing the Standard Source Files 5.3.3 Adding Hardware Setup Files File name: Files of type: Look in: 5.3.4 Setting Compiler Options 5.3.5 Setting Linker Options Page Page Page Page Page Page 5.3.6 Writing the Main Function (Operation Confirmation)