Manuals / Brands / Computer Equipment / Computer Hardware / Renesas / Computer Equipment / Computer Hardware

Renesas M3A-HS71, SH7670 Creating and Running a New Project Workspace , 5.3 Adding/Modifying Hardware Setup Files

1 80

Download 80 pages, 2.37 Mb

Creating and Running a New Project Workspace

5.2.3 Activating the Command Line Window

Rev. 1.01 May 7, 2008 5-10

REJ11J0015-0101

5

5.2.3 Activating the Command Line Window

Choose Command Line from the View menu and open the Command Line window.

When downloading the load modules, activate the Command Line window to check whether the script file is running.

Note: Unless the script file is running, you cannot download the load modules into the flash memory. So be sure to

check this.

5.3 Adding/Modifying Hardware Setup Files

For the software to be run on the SH7670 CPU board, the hardware dependent part of the SH7670 CPU board must

be set up.

Here, the hardware dependent part of the SH7670 CPU board is added or modified for the standard source files that

were automatically generated when you created a new project. The procedure for adding/modifying hardware setup

files is described below.

The setting of the hardware dependent part indicates the settings of external memory (flash memory, SDRAM)

access timing, the operating clock and the cache memory.

5.3.1 Copying Hardware Setup Files

Copy “HardwareSetup” directory from the CD-ROM into the directory for the new project workspace

"C:¥WorkSpace¥test" that you created previously.

The explanation given below assumes that the hardware setup files are stored in

"C:¥WorkSpace¥test¥HardwareSetup" directory.

5.3.2 Removing the Standard Source Files

(1) Select [Project Æ Remove Files...].

Figure 5.3.1 Setting Up to Removing Files (1)

Contents

Main REJ11J0015-0101 Rev. 1.01 Issued: May 7. 2008 Renesas 32-Bit RISC Microcomputers SuperHTM RISC engine Family/SH7670 Series M3A-HS71 Installation Manual SH7670 CPU Board Page Page Page [Indication of Warnings and Cautions] Page Important About this product: Purpose of use of this product: For those who use this product: When using this product: Page Usage restrictions: About product changes: About the rights: About diagrams: Page Table of Contents CHAPTER5 CREATING AND RUNNING A NEW PROJECT WORKSPACE ..................................... 5-1 Page Page Page Page Before Using the SH7670 CPU Board 1.1 Overview To Ensure Safe and Correct Use These pictorial indications are explained in the section 1.2, Usage Precautions. Please be sure 1.2 Usage Precautions Do not let foreign matters such as water, pieces of metal or inflammable material get into the The upper-limit ambient temperature at which this product can be used (i.e., rated maximum 1.2.1 Symbols Used Before Using the SH7670 CPU Board 1.3 Procedure for Introducing This Product 1.4 Operating Guarantee for This Product Before Using the SH7670 CPU Board 1.5 Items to Be Prepared by User 1.5.1 Recommended Host Computer Environment Page Page Setting Up the Hardware 2.1 Connections Between SH7670 CPU board and E10A-USB Emulator 2.2 SH7670 CPU board Switch Setting Do not change DIP switch and jumper settings while the SH7670 CPU board is operating. Always 2.2.1 SH7670 CPU board DIP Switch Setting 2.2.2 SH7670 CPU Board Jumper Switch Setting Board edge ON SW8 Setting Up the Hardware 2.3 System Connections and Power-On Sequence Unless the above power-on sequence is followed, unrecoverable damage may occur to the Page Setting Up the Software 3.1 About the HEW 3.1.1 HEW Installation Procedure Page Page Setting Up the Software 3.2 Setting Up the E10A-USB Emulator Software 3.2.1 E10A-USB Software Installation Procedure Page Page Page 3.2.2 Setting Up the E10A-USB Emulator Page Page Do not turn off the power for the host computer or remove the USB cable while the system is Page Page Page Page Page Page Page Running the Software 4.1 Running the Software 4.1.1 Preparing for Downloading the Sample Software 4.1.2 SH7670 CPU board and E10A-USB Startup Procedure (HEW Startup) Page Page Page 4.1.3 E10A-USB Emulator Connection Error Dialog Page 4.1.4 Sample Software Download Procedure Page Page Page Running the Softwareare Page Creating and Running a New Project Workspace 5.1 Creating a New Project Workspace 5.1.1 Preparing for Creating a New Project Workspace 5.1.2 Procedure for Creating a New Project Workspace Page Page Page Page Page Creating and Running a New Project Workspace 5.2 Setting Up the Flash Memory Download 5.2.1 Setting Up the Flash Memory Download Function 5.2.2 Specifying the Command Batch File Before Downloading Creating and Running a New Project Workspace 5.2.3 Activating the Command Line Window 5.3 Adding/Modifying Hardware Setup Files 5.3.1 Copying Hardware Setup Files 5.3.2 Removing the Standard Source Files 5.3.3 Adding Hardware Setup Files File name: Files of type: Look in: 5.3.4 Setting Compiler Options 5.3.5 Setting Linker Options Page Page Page Page Page Page 5.3.6 Writing the Main Function (Operation Confirmation)