Manuals / Brands / Computer Equipment / Computer Hardware / Renesas / Computer Equipment / Computer Hardware

Renesas M3A-HS71, SH7670 4.1.3 E10A-USB Emulator Connection Error Dialog

1 80

Download 80 pages, 2.37 Mb

Running the Software

4.1.3 E10A-USB Emulator Connection Error Dialog

Rev. 1.01 May 7, 2008 4-6

REJ11J0015-0101

4

4.1.3 E10A-USB Emulator Connection Error Dialog

If the E10A-USB emulator does not start up, the dialog box shown below will be displayed.

(a) If the dialog box shown below is displayed and the E10A-USB emulator cannot be started by the method in (11) on the

previous page, the SH7670 CPU board may not be supplied with the system power. Check the power supply for the

SH7670 CPU board.

Figure 4.1.9 Can not find /RESET signal Dialog Box

(b) If the dialog box shown below is displayed, the H-UDI pins and the H-UDI port connector may not be connected

correctly. Check the connection between the H-UDI pins and the H-UDI port connector.

Figure 4.1.10 Check the Connection Dialog Box

(c) If the dialog box shown below is displayed, the E10A-USB emulator firmware may not be set up correctly. Use the

setup tool or the additional license tool to set up the firmware for the device group that you use.

Figure 4.1.11 Product Currently Connected Dialog Box

(d) If the dialog box shown below is displayed, the firmware version set up in the E10A-USB may be old. Use the setup tool

to set up the appropriate version of firmware.

Figure 4.1.12 Version of the Emulator Firmware Dialog Box

Contents

Main REJ11J0015-0101 Rev. 1.01 Issued: May 7. 2008 Renesas 32-Bit RISC Microcomputers SuperHTM RISC engine Family/SH7670 Series M3A-HS71 Installation Manual SH7670 CPU Board Page Page Page [Indication of Warnings and Cautions] Page Important About this product: Purpose of use of this product: For those who use this product: When using this product: Page Usage restrictions: About product changes: About the rights: About diagrams: Page Table of Contents CHAPTER5 CREATING AND RUNNING A NEW PROJECT WORKSPACE ..................................... 5-1 Page Page Page Page Before Using the SH7670 CPU Board 1.1 Overview To Ensure Safe and Correct Use These pictorial indications are explained in the section 1.2, Usage Precautions. Please be sure 1.2 Usage Precautions Do not let foreign matters such as water, pieces of metal or inflammable material get into the The upper-limit ambient temperature at which this product can be used (i.e., rated maximum 1.2.1 Symbols Used Before Using the SH7670 CPU Board 1.3 Procedure for Introducing This Product 1.4 Operating Guarantee for This Product Before Using the SH7670 CPU Board 1.5 Items to Be Prepared by User 1.5.1 Recommended Host Computer Environment Page Page Setting Up the Hardware 2.1 Connections Between SH7670 CPU board and E10A-USB Emulator 2.2 SH7670 CPU board Switch Setting Do not change DIP switch and jumper settings while the SH7670 CPU board is operating. Always 2.2.1 SH7670 CPU board DIP Switch Setting 2.2.2 SH7670 CPU Board Jumper Switch Setting Board edge ON SW8 Setting Up the Hardware 2.3 System Connections and Power-On Sequence Unless the above power-on sequence is followed, unrecoverable damage may occur to the Page Setting Up the Software 3.1 About the HEW 3.1.1 HEW Installation Procedure Page Page Setting Up the Software 3.2 Setting Up the E10A-USB Emulator Software 3.2.1 E10A-USB Software Installation Procedure Page Page Page 3.2.2 Setting Up the E10A-USB Emulator Page Page Do not turn off the power for the host computer or remove the USB cable while the system is Page Page Page Page Page Page Page Running the Software 4.1 Running the Software 4.1.1 Preparing for Downloading the Sample Software 4.1.2 SH7670 CPU board and E10A-USB Startup Procedure (HEW Startup) Page Page Page 4.1.3 E10A-USB Emulator Connection Error Dialog Page 4.1.4 Sample Software Download Procedure Page Page Page Running the Softwareare Page Creating and Running a New Project Workspace 5.1 Creating a New Project Workspace 5.1.1 Preparing for Creating a New Project Workspace 5.1.2 Procedure for Creating a New Project Workspace Page Page Page Page Page Creating and Running a New Project Workspace 5.2 Setting Up the Flash Memory Download 5.2.1 Setting Up the Flash Memory Download Function 5.2.2 Specifying the Command Batch File Before Downloading Creating and Running a New Project Workspace 5.2.3 Activating the Command Line Window 5.3 Adding/Modifying Hardware Setup Files 5.3.1 Copying Hardware Setup Files 5.3.2 Removing the Standard Source Files 5.3.3 Adding Hardware Setup Files File name: Files of type: Look in: 5.3.4 Setting Compiler Options 5.3.5 Setting Linker Options Page Page Page Page Page Page 5.3.6 Writing the Main Function (Operation Confirmation)