Manuals / Brands / Computer Equipment / Computer Hardware / Renesas / Computer Equipment / Computer Hardware

Renesas M3A-HS71, SH7670 Creating and Running a New Project Workspace , 5.2 Setting Up the Flash Memory Download

1 80

Download 80 pages, 2.37 Mb

Creating and Running a New Project Workspace

5.2 Setting Up the Flash Memory Download

Rev. 1.01 May 7, 2008 5-8

REJ11J0015-0101

5

5.2 Setting Up the Flash Memory Download

Next, the following shows how to set up the function for downloading load modules into the flash memory connected

external to the SH7670 CPU board.

Here, we use the flash memory download program stored in

"C:¥ WorkSpace¥Sample_software¥sh7670_sample¥fmtool_hs71.

For details about flash memory download settings, refer to the “SuperH Family E10A-USB Emulator User’s Manual.”

5.2.1 Setting Up the Flash Memory Download Function

Setting up the flash memory download function

From [Setup] menu Æ [Emulator] Æ [System…], select [Configuration] dialog box, and open [Loading flash memory]

page.

For “File Name” here, specify the flash memory download program (fmtool_hs71.mot). The sample workspace is

assumed to have the flash memory download program stored in the directory indicated below.

" C:¥WorkSpace¥Sample_software¥sh7670_sample¥fmtool_hs71"

Figure 5.2.1

Set up “Loading flash memory”, “File name”, “Bus width of flash memory” and “Entry point” as shown in

and Table5.2.1. Then click “OK”

Note: Loading Flash Memory is set to “Disable” in the default setting. Therefore, you need to enable it whenever you

connect the E10A-USB emulator.

Select “Enable”

Specify the path to

the fmtool_71.mot file.

Set the bus width to 16 bits.

Set H'FFF80000

for the write module address.

Figure 5.2.1 Configuration Dialog Box

Contents

Main REJ11J0015-0101 Rev. 1.01 Issued: May 7. 2008 Renesas 32-Bit RISC Microcomputers SuperHTM RISC engine Family/SH7670 Series M3A-HS71 Installation Manual SH7670 CPU Board Page Page Page [Indication of Warnings and Cautions] Page Important About this product: Purpose of use of this product: For those who use this product: When using this product: Page Usage restrictions: About product changes: About the rights: About diagrams: Page Table of Contents CHAPTER5 CREATING AND RUNNING A NEW PROJECT WORKSPACE ..................................... 5-1 Page Page Page Page Before Using the SH7670 CPU Board 1.1 Overview To Ensure Safe and Correct Use These pictorial indications are explained in the section 1.2, Usage Precautions. Please be sure 1.2 Usage Precautions Do not let foreign matters such as water, pieces of metal or inflammable material get into the The upper-limit ambient temperature at which this product can be used (i.e., rated maximum 1.2.1 Symbols Used Before Using the SH7670 CPU Board 1.3 Procedure for Introducing This Product 1.4 Operating Guarantee for This Product Before Using the SH7670 CPU Board 1.5 Items to Be Prepared by User 1.5.1 Recommended Host Computer Environment Page Page Setting Up the Hardware 2.1 Connections Between SH7670 CPU board and E10A-USB Emulator 2.2 SH7670 CPU board Switch Setting Do not change DIP switch and jumper settings while the SH7670 CPU board is operating. Always 2.2.1 SH7670 CPU board DIP Switch Setting 2.2.2 SH7670 CPU Board Jumper Switch Setting Board edge ON SW8 Setting Up the Hardware 2.3 System Connections and Power-On Sequence Unless the above power-on sequence is followed, unrecoverable damage may occur to the Page Setting Up the Software 3.1 About the HEW 3.1.1 HEW Installation Procedure Page Page Setting Up the Software 3.2 Setting Up the E10A-USB Emulator Software 3.2.1 E10A-USB Software Installation Procedure Page Page Page 3.2.2 Setting Up the E10A-USB Emulator Page Page Do not turn off the power for the host computer or remove the USB cable while the system is Page Page Page Page Page Page Page Running the Software 4.1 Running the Software 4.1.1 Preparing for Downloading the Sample Software 4.1.2 SH7670 CPU board and E10A-USB Startup Procedure (HEW Startup) Page Page Page 4.1.3 E10A-USB Emulator Connection Error Dialog Page 4.1.4 Sample Software Download Procedure Page Page Page Running the Softwareare Page Creating and Running a New Project Workspace 5.1 Creating a New Project Workspace 5.1.1 Preparing for Creating a New Project Workspace 5.1.2 Procedure for Creating a New Project Workspace Page Page Page Page Page Creating and Running a New Project Workspace 5.2 Setting Up the Flash Memory Download 5.2.1 Setting Up the Flash Memory Download Function 5.2.2 Specifying the Command Batch File Before Downloading Creating and Running a New Project Workspace 5.2.3 Activating the Command Line Window 5.3 Adding/Modifying Hardware Setup Files 5.3.1 Copying Hardware Setup Files 5.3.2 Removing the Standard Source Files 5.3.3 Adding Hardware Setup Files File name: Files of type: Look in: 5.3.4 Setting Compiler Options 5.3.5 Setting Linker Options Page Page Page Page Page Page 5.3.6 Writing the Main Function (Operation Confirmation)