Ricoh MIB-II - page 75

Operating Instructions Administrator Reference

Note

❒If you configure the NetWare printing environment by using SmartNetMonitor for Admin under

the following environments, NetWare Client provided by Novell is requir ed.

•NDS mode in Windows 95/98/Me

•NDS or Bindary mode in Windows 2000/Windows NT 4.0

❒Use the version of Novell Client provided with your operating system or the la test version.

❖

❖❖

❖Printers listed by SmartNetMonitor for Admin

SmartNetMonitor for Admin displays a list of printers, which are connected to the network.

If you cannot find out the printer from the displayed list, refer to the configuration page printed

from the printer. For more information about printing a configuration page, see p.130 “Printing

a Configuration Page”.

Contents

Main 1.Windows 2000 Print Server Configuration 2.Windows XP Print Server Configuratio n 3.Windows NT 4.0 Print Server Configuration 4.NetWare Config uration 5.Using SmartNetMonitor for Admin 6.Using a Web Browser 7.Monitoring and Configurin g the Printer 8.Making Printer Settings with the Control Panel 9.Appendix Page Introduction Page How to Read This Manual Symbols Page Confirming a Network Environment Print Server Configuration Netware Configuration 1. Windows 2000 Print Server Configuration Page Page Page Page Page Page Page Page Page Page F Page Page Page Page Page Page Page Page 2. Windows XP Print Server Configuration Configuring the printer C:> ping 192.168.15.16 Request timed out. Reply from 192.168.15.16 Page Page Page Page Page Page Page Page Page Standard TCP/IP Port Page Page Page Page Page Page 3. Windows NT 4.0 Print Server Configuration Configuring the printer Page Page Page Page Page Page Page Page Page Page E F Page Page Page Page Page Page Page Page Page G GG G Active Protocol: TCP/IP NetWare: *Active H HH H SmartNetMonitor for Admin Network Setup: Frame Type (NW) Frame Type (NW): *Auto Ready Page Page Page Page Page Page K KK K L LL L Page NetWare 4.x, 5 - Advanced Settings Page Page Page Page Page Page Page M MM M N NN N 5. Using SmartNetMonitor for Admin Select the appropriate protocol stack for your operating system. Page Page Page Page Page Page Page 6. Using a Web Browser Going to the Top Page http://192.168.15.16/ \HELP\WSMHLP\(Language)\ 1. Page E Page D Page 7. Monitoring and Configuring the Printer Changing Names and Comments Page Page Page Page Page Page Page 8. Making Printer Settings with the Control Panel Menu Chart Page Page Page Accessing the Main Menu Page Paper Input Menu Paper Input Parameters Page Page Changing the Paper Input Menu Tray Locking Menu: Paper Input Paper Input: Tray Locking Tray Locking: Tray 1 Tray 1: *Off Tray Priority Menu: Paper Input Paper Input: Tray Priority Page List/Test Print Menu List/Test Print Parameters Page Page Page Interpreting the Configuration Page Page Page Maintenance Menu Maintenance Menu Parameters Page Reference Page Page Maintenance: Color Regist. Maintenance: Menu Protect Menu Protect: *Off Page Displaying the Signal Strength Maintenance: Color Regist. Menu: Maintenance Page G GG G Ready Page Page System Menu System Parameters Default: On Default: Off Page Page Page Page Page Page C D System : MisfeedRecovery System : E. Saver2 Timer Page Host Interface Menu Host Interface Parameters Default: 128 KB Default: 15 seconds Page Page Page Page Page Page Page Page Page Page PCL Menu PCL Parameters Page Page Page PCL Menu: Orientation Orientation: *Portrait Page Language Menu Changing the Language Menu Page Page 9. Appendix SNMP Spool Printing Page Page D msh> logout msh> help command_name E Commands List Page Page Page Page Protocol Use the set command to allow/prevent remote access for each protocol. msh> set protocol {up | down} Printer status msh> command Network Interface Board configuration settings information msh> show [-p] System log information msh> syslog SNMP Page Page Page Page Page SMB msh >smb parameter ROUTE SLP msh> slp ttl {1 -255} Page Page Page Page Changing the Host Name msh> hostname [interface_name ] printer_name SNTP Page Page Getting Printer Information over the Network Printer current status Page Printer configuration You can check the printer configuration using telnet. telnet Use the info command. "*" (asterisk) is displayed with the current setting. Regarding *1 - *5, see the following table. *1 Input Tray: Name *2 Input Tray: PaperSize *3 Input Tray: Status Page Understanding the Displayed Information Print Job Information Print Log Information Configuring the Network Interface Board Page Page Page Page Message List System Log Information Page Page Page Page Page Page Page Page Precautions Connecting a Dial Up Router to a Network Configuring the router Page PostScript Printing from Windows NetWare Printing Form Feed Banner Page Printing after resetting the printer Using DHCP Using AutoNet Page Page Memory Capacity and Paper Size Reference For more information about how to set the printer driver, see printer driver's He lp. Page Specifications Mainframe Page Page Page Options Page Page Page Page Page Information about Installed Software expat http://expat.sourceforge.net/ JPEG LIBRARY NetBSD Authors Name List Page INDEX A B C D E F G H I L M N O P R S T U W