Manuals / Roberts Gorden / Household Appliance / Electric Heater

Roberts Gorden BH-125 Description, Distance A, Extension, Part Number, Minimum, Maximum, Part No

Models: BH-125 BH-80 BH-200 BH-140 BH-100 BH-115 BH-175 BH-150 BH-40 BH-60

1 70

Download 70 pages 23.9 Kb

Page 39

Image 39

SECTION 7: OPTIONAL HEATER ACCESSORIES

Step 7.5.2 Frame Shield Installation

Description	Part Number
Deco Grille Shield	01365900

Step 7.5.3 Reflector Side Extension Installation for Decorative Grilles

Distance "A"		Extension
Minimum	Maximum	Part No.	Width

2" (4 cm)	6" (15 cm)	01370408	8" (20 cm)
6" (15 cm)	10" (26 cm)	01370412	12" (30 cm)

10" (26 cm)	14" (37 cm)	01370416	16" (40 cm)

Description	Part Number
Reflector Side Extension	01370412

33 of 59

Page 39

Image 39

Roberts Gorden BH-125, BH-60, BH-40, BH-80 Description, Distance A, Extension, Part Number, Minimum, Maximum, Part No, Width

Contents

If you smell gas Installation, Operation &Blackheat BH BH-115 BH-200Page 2012 Roberts-GordonLLC TABLE OF CONTENTSPage LIST OF TABLES TABLE OF FIGURESPage 1.3 California Proposition SECTION 1: HEATER SAFETY1.1 Manpower Requirements 1.2 Safety Labels and Their PlacementBottom Panel Gas Connection LabelTop Panel Logo LabelPart Number FIGURE 2: Side and Back Panel Label Placement3 of DescriptionProduct Damage Hazard SECTION 2: INSTALLER RESPONSIBILITY2.1 Wall Tag 2.2 Corrosive ChemicalsFire Hazard FIGURE 3: Standard Reflector FIGURE 6: 45 Tilt Reflector Page inches FIGURE 12: Venting4.4 Electrical 4.1 Gas Codes4.2 Aircraft Hangars 4.3 Public GaragesSECTION 5: MAJOR COMPONENTS 12 of 5.1 Standard Parts ListAluminized Core PackagesMinimum StandardSECTION 6: HEATER INSTALLATION Typical Suspension Details FIGURE 14: Critical Hanger Placement16 of FIGURE 15: Linear Heater Assembly OverviewFIGURE 16: Linear Heater Layout Overview 17 ofPart Number Step 6.1 Burner Tube Installation18 of DescriptionStep 6.3 Coupling and Tube Assembly Step 6.2 Tube Clamp Package InstallationStep 6.3.1 Coupling and Tube Assembly Continued Step 6.3.2 Coupling and Tube Assembly Continued± 2 5 cm 21 of Step 6.4 Turbulator InstallationTurbulator must be installed in the last not required on the BH-125/150/175/200Step 6.5 Reflector Installation To ensure proper expansion and contraction reflector supports and U-clipsdepend on the23 of Part Number Step 6.6 Burner Installation24 of DescriptionEdges are sharp SECTION 7: OPTIONAL HEATER ACCESSORIES7.1 U-TubeConfiguration Cut/Pinch HazardLoose U-bolt FIGURE 18: U-TubeHeater Assembly Overview26 of Tight U-boltFIGURE 19: U-TubeHeater Layout Overview LEGEND27 of 28 of FIGURE 20: U-TubeLayout Overview ContinuedSECTION 7 OPTIONAL HEATER ACCESSORIES Step 7.2.2 Elbow InstallationStep 7.2.3 Reflector Joint Installation Step 7.2.4 Reflector Joint InstallationStep 7.2.5 Reflector Joint Detail FIGURE 21: Reflector Joint Detail30 of 31 of Step 7.3.1 Bracket InstallationStep 7.3.2 Side Reflector Installation 7.3 Reflector Side ExtensionDescription DescriptionPart Number Lower Clearance Shield PackageExtension SECTION 7: OPTIONAL HEATER ACCESSORIESDescription Distance AStep 7.6.3 Grille Installation Step 7.6.2 Grille End Cap InstallationSECTION 8: VENTING 8.5 Unvented Operation Tube Termination 8.2 Unvented Operation8.3 Horizontal Venting 8.4 Vertical Venting•Heaters must be of the same BTU output 8.8 Vertical Ventilation 4 10 cm Pipe8.9 Common Side Wall Venting Requirements38 of 8.10 Common Vertical VentingRequirements •Heaters must be of the same BTU output8.11.1 Length Requirements 8.11 Outside Combustion Air SupplyRequirements Requirements40 of SECTION 9: GAS PIPING CORRECT POSITIONS when attaching gas hoseINCORRECT POSITIONS WRONG INSTALLATION FIGURE 23: Gas Connection with Flexible Gas Hose10.1 Line Voltage Thermostat Wiring DANGERSECTION 10: WIRING Disconnect electric before service44 of 10.2 Low Voltage Thermostat Wiring10.3 Internal Wiring SECTION 10: WIRING45 of Green to Gnd Connect wires together withBX or Romex Connector Internal Wire Bundle Burner BoxDANGER SECTION 11: OPERATION AND MAINTENANCE11.5 Maintenance Checklist See Page 5, SectionSee Page 35, Section See Page 14, SectionSee Page 32, Section See Page 43, SectionSee Page 15, Figure See Page 32, Section 7.5 and Page 34, SectionDANGER SECTION 12: TROUBLESHOOTING51 of 12.1 Troubleshooting Flow Chart52 of 12.2 Manifold Gas Pressure Setting SECTION 12: TROUBLESHOOTING53 of DANGER SECTION 13: REPLACEMENT PARTS55 of SECTION 13 REPLACEMENT PARTS56 of DescriptionPart Number SECTION 14: GENERAL SPECIFICATIONS 58 of LIMITATIONS ON AUTHORITY OF REPRESENTATIVES WARRANTY IS VOID IFROBERTS-GORDONLLC WILL PAY FOR ROBERTS-GORDONLLC WILL NOT PAY FORPage Page Page

Distance "A"

Extension

Maximum

Part No.

Width