Manuals / Roberts Gorden / Household Appliance / Electric Heater

Roberts Gorden BH-40, BH-60, BH-150, BH-175, BH-115, BH-100, BH-140, BH-200, BH-80 Internal Wiring

Models: BH-125 BH-80 BH-200 BH-140 BH-100 BH-115 BH-175 BH-150 BH-40 BH-60

1 70

Download 70 pages 23.9 Kb

Page 51

SECTION 10: WIRING

10.3 Internal Wiring

45 of 59

Image 51

Roberts Gorden BH-40, BH-60, BH-150, BH-175, BH-115, BH-100, BH-140, BH-200, BH-80, BH-125 service manual Internal Wiring

Contents

Installation must be done by a contractor qualified Improper installation, adjustment, alteration, serviceOr maintenance can result in death, injury or Property damage. Read the Installation, OperationPage Roberts-Gordon LLC Page Table of Figures Page California Proposition Heater SafetyManpower Requirements Safety Labels and Their Placement Top and Bottom Panel Label Placement Side and Back Panel Label Placement Installer Responsibility Wall TagNational Standards and Applicable Codes Clearances are the required distances that Maintain clearances to combustibles at all times for safety Model InchesC D Centimeters Tube, Standard Reflector Model 45 Tilt Reflector Model Inches Centimeters Tube, Opposite 45 Reflector Model Centimeters Model Venting Inches National Standards and Applicable Codes Reflector End Cap Major ComponentsStainless Steel Burner Tube Standard Parts List Contents of BH-Series Burner CartonContents of Core and Extension Packages BH-Series Component Package Guide Model Tubing Length Core Packages Minimum Standard Aluminized Heater Installation Typical Suspension Details Linear Heater Assembly Overview Linear Heater Layout Overview Linear Heater Layout Overview Burner Tube Installation Closed Tube Clamp Package InstallationCoupling and Tube Assembly Open 2 Coupling and Tube Assembly 1 Coupling and Tube Assembly Not required on the BH-125/150/175/200 Turbulator Installation Hanger Burner Tube Reflector Description Part Number Reflector Support Package 1 Reflector, U-Clip and Reflector Support Installation Burner Installation Optional Heater Accessories Tube, Standard TubeTube, Opposite Tube Heater Layout Overview Tube Layout Overview Elbow Package Configuration .2.1 Elbow Installation 2 Elbow Installation Reflector Joint Detail 5 Reflector Joint Detail 2 Side Reflector Installation Reflector Side Extension 1 Bracket Installation Description Part Number Lower Clearance Shield Package Distance a Extension 2 Frame Shield Installation 3 Grille Installation 2 Grille End Cap Installation Venting United States RequirementsCanadian Requirements Unvented Operation Tube Termination Unvented OperationHorizontal Venting Vertical Venting Vertical Ventilation 4 10 cm Pipe Common Side Wall VentingOutside Wall Common Vertical Venting Outside Combustion Air Supply Vertical Outside Air Supply for Single Heater Installation Horizontal Outside Air Supply for Double Heater Installation Vertical Outside Air Supply for Double Heater Installation GAS Piping Failure to follow these instructions can result When attaching gas hoseCorrect Positions Hold gas nipple securely with pipe wrench Line Voltage Thermostat Wiring Wiring Front View Low Voltage Thermostat Wiring Internal Wiring Ladder Diagram Electrical Connection to the Burner To Shut Off Heater Operation and MaintenancePre-Season Maintenance and Annual Inspection Sequence of Operation Reflector Vicinity of the HeaterVehicles and Other Objects Electrode Safety LabelsBlower Scroll, Wheel Motor Burner Cup and Orifice Troubleshooting YES Troubleshooting Flow ChartPage Manifold Gas Pressure Setting Replacement Parts Replacement Parts Description Part Number Pipe Connection General SpecificationsDimensions GAS Pressure AT ManifoldPage Limitations on Authority Representatives Warranty is Void ifROBERTS-GORDON LLC will PAY for ROBERTS-GORDON LLC will not PAY forPage Page Page