Manuals / Roberts Gorden / Household Appliance / Electric Heater

Roberts Gorden BH-60, BH-40, BH-150, BH-175, BH-115 Grille End Cap Installation, Grille Installation

Models: BH-125 BH-80 BH-200 BH-140 BH-100 BH-115 BH-175 BH-150 BH-40 BH-60

1 70

Download 70 pages 23.9 Kb

Page 40

BH-SERIES INSTALLATION, OPERATION AND SERVICE MANUAL

7.6Protective Grille Installation Step 7.6.1 Silicone Cap Installation

	Silicone Cap
Grille	Description	Part Number
Finger	Grille Section	08050001
	Grille End Cap	08050002
	Silicone Cap	91915951-6P

Step 7.6.2 Grille End Cap Installation
A	B
Grille	Grille End Cap
C	D
	Bend up 90°.
	Pull outward.

Step 7.6.3 Grille Installation

Reflector

40"

(101 cm)

Final Grille

Section

Grille

Grille

End Cap

34 of 59

Image 40

Roberts Gorden BH-60, BH-40, BH-150, BH-175, BH-115, BH-100, BH-140, BH-200 Grille End Cap Installation, Grille Installation

Contents

Improper installation, adjustment, alteration, service Or maintenance can result in death, injury orProperty damage. Read the Installation, Operation Installation must be done by a contractor qualifiedPage Roberts-Gordon LLC Page Table of Figures Page Heater Safety Manpower RequirementsSafety Labels and Their Placement California Proposition Top and Bottom Panel Label Placement Side and Back Panel Label Placement Wall Tag Installer ResponsibilityNational Standards and Applicable Codes Maintain clearances to combustibles at all times for safety Clearances are the required distances that Inches C DCentimeters Model 45 Tilt Reflector Model Tube, Standard Reflector Model Tube, Opposite 45 Reflector Model Inches Centimeters Venting Inches Centimeters Model National Standards and Applicable Codes Major Components Stainless SteelBurner Tube Reflector End Cap Contents of BH-Series Burner Carton Standard Parts ListContents of Core and Extension Packages Core Packages Minimum Standard Aluminized BH-Series Component Package Guide Model Tubing Length Heater Installation Typical Suspension Details Linear Heater Assembly Overview Linear Heater Layout Overview Burner Tube Installation Linear Heater Layout Overview Tube Clamp Package Installation Coupling and Tube AssemblyOpen Closed 1 Coupling and Tube Assembly 2 Coupling and Tube Assembly Turbulator Installation Not required on the BH-125/150/175/200 Hanger Burner Tube Reflector 1 Reflector, U-Clip and Reflector Support Installation Description Part Number Reflector Support Package Burner Installation Optional Heater Accessories Tube Tube, StandardTube, Opposite Tube Heater Layout Overview Elbow Package Configuration .2.1 Elbow Installation Tube Layout Overview 2 Elbow Installation 5 Reflector Joint Detail Reflector Joint Detail Reflector Side Extension 1 Bracket Installation 2 Side Reflector Installation Description Part Number Lower Clearance Shield Package 2 Frame Shield Installation Distance a Extension 2 Grille End Cap Installation 3 Grille Installation United States Requirements VentingCanadian Requirements Unvented Operation Horizontal VentingVertical Venting Unvented Operation Tube Termination Common Side Wall Venting Vertical Ventilation 4 10 cm PipeOutside Wall Common Vertical Venting Vertical Outside Air Supply for Single Heater Installation Outside Combustion Air Supply Vertical Outside Air Supply for Double Heater Installation Horizontal Outside Air Supply for Double Heater Installation GAS Piping When attaching gas hose Correct PositionsHold gas nipple securely with pipe wrench Failure to follow these instructions can result Wiring Line Voltage Thermostat Wiring Low Voltage Thermostat Wiring Front View Internal Wiring Ladder Diagram Electrical Connection to the Burner Operation and Maintenance Pre-Season Maintenance and Annual InspectionSequence of Operation To Shut Off Heater Vicinity of the Heater Vehicles and OtherObjects Reflector Safety Labels Blower Scroll, WheelMotor Burner Cup and Orifice Electrode Troubleshooting Troubleshooting Flow Chart YESPage Manifold Gas Pressure Setting Replacement Parts Replacement Parts Description Part Number General Specifications DimensionsGAS Pressure AT Manifold Pipe ConnectionPage Warranty is Void if ROBERTS-GORDON LLC will PAY forROBERTS-GORDON LLC will not PAY for Limitations on Authority RepresentativesPage Page Page