TABLE OF CONTENTS
SECTION 1: Heater Safety | 1 | SECTION 12: Control Methods | 42 | ||
1.1 Manpower Requirements | 1 | 12.1 ROBERTS GORDON® System Control | 42 | ||
SECTION 2: Installer Responsibility | 2 | 12.2 ROBERTS GORDON® ULTRAVACTM | 42 | ||
2.1 | Wall Tag | 2 | 12.3 | SPST Transformer Relay (P/N 90417600) | 42 |
2.2 | Corrosive Chemicals | 2 | 12.4 | DPST Transformer Relay (P/N 90436300) | 42 |
2.3 | National Standards and Applicable Codes | 2 | SECTION 13: Starting The System | 49 | |
SECTION 3: Critical Considerations | 3 | 13.1 | Checking the Gas Line | 49 | |
3.1 | Required Clearances to Combustibles | 3 | 13.2 | Checking the Electrical System | 49 |
SECTION 4: National Standards and Applicable Codes | 7 | 13.3 | Starting the System | 49 | |
4.1 | Gas Codes | 7 | 13.4 | Setting the Vacuum | 49 |
4.2 | Aircraft Hangars | 7 | SECTION 14: Operation and Maintenance | 51 | |
4.3 | Public Garages | 7 | 14.1 | Sequence of Operation | 51 |
4.4 | Electrical | 7 | 14.2 | To Shut Off Heater | 51 |
4.5 | Venting | 7 | 14.3 | To Start Heater | 51 |
4.6 | High Altitude | 7 | 14.4 | 51 | |
SECTION 5: Major Components | 8 | 14.5 | Maintenance Checklist | 52 | |
5.1 | Standard Parts List | 11 | SECTION 15: Troubleshooting | 55 | |
SECTION 6: Design Requirements | 13 | 15.1 | Troubleshooting Flow Chart | 55 | |
SECTION 7: Heater Installation | 15 | SECTION 16: Replacement Parts | 57 | ||
7.1 | Tube Installation | 16 | SECTION 17: General Specifications | 58 | |
7.2 | Coupling and Tube Assembly | 16 | 17.1 Material Specification | 58 | |
7.3 Elbow Package Configuration | 17 | 17.2 Heater Specifications | 58 | ||
7.4 | Reflector Installation | 18 | 17.3 Suspension Specifications | 58 | |
7.5 | Burner Installation | 20 | 17.4 Controls Specifications | 58 | |
SECTION 8: Optional Heater Accessories | 21 | SECTION 18: The ROBERTS GORDON® CORAYVAC® |
| ||
8.1 | Tee Installation | 21 |
| Limited Warranty | 61 |
8.2 | Reflector Joint | 21 |
|
|
|
8.3 | Reflector Side Extension | 23 |
|
|
|
8.4 | Universal Shield | 24 |
|
|
|
8.5 | Barrier Shield | 24 |
|
|
|
8.6 | 25 |
|
|
| |
8.7 | 26 |
|
|
| |
8.8 | Protective Grille Installation | 29 |
|
|
|
8.9 | Classic | 30 |
|
|
|
SECTION 9: Pump Installation and Venting | 31 |
|
|
| |
9.1 | Pump Installation | 31 |
|
|
|
9.2 | General Venting Requirements Model |
|
|
|
|
| 32 |
|
|
| |
9.3 | Horizontal Venting 4" (10 cm) Pipe | 34 |
|
|
|
SECTION 10: Outside Air Supply | 37 |
|
|
| |
10.1 Pressurized | 37 |
|
|
| |
10.2 | 37 |
|
|
| |
10.3 Outside Air Blower Internal Wiring | 38 |
|
|
| |
SECTION 11: Gas Piping | 41 |
|
|
|
©2006 ROBERTS GORDON, LLC
All rights reserved. No part of this work covered by the copyrights herein may be reproduced or copied in any form or by any means - graphic, electronic, or mechanical, including photocopying, recording, taping or information storage and retrieval systems - without the written permission of
Printed in U.S.A.