127
Adding Effects

In Performance mode you can use three multi-effects (MFX1, MFX2, MFX3), one chorus, and one reverb. For each of the three multi-effects, the
chorus, and the reverb, you can specify whether it will operate according to the effect settings of the performance, or according to the effect
settings of the patch or rhythm set assigned to the part you specify. The three multi-effects can be used independently, or you can connect two or
three of them in series.
Here you can make overall settings for effects, and the output destination and level of each signal.

fig.RoutingPfm

For details on these settings, refer to

Making Effect Settings

(p. 125).

* For the following parameters , – , and settings can be made individually for three systems multi-effects (MFX1–MFX3).

MFX Output As-
sign
A, B Output destination of the sound passed through the multi-effects
A:
OUTPUT A (MIX) jacks in stereo
B:
OUTPUT B jacks in stereo
* If the Mix/Parallel parameter is set to “MIX,” all sounds are output from the OUTPUT A (MIX) jacks in stereo (p. 158).

Chorus Output
Select
MAIN, REV,
M+R
Specifies how the sound routed through chorus will be output.
MAIN:
Output to the OUTPUT jacks in stereo.
REV:
Output to reverb in mono.
M+R:
Output to the OUTPUT jacks in stereo, and to reverb in mono.
Chorus Level 0–127 Volume of the sound passed through chorus
Chorus Output
Assign
A, B Selects the pair of OUTPUT jacks to which the chorus sound is routed when Chorus Output Select is set to “MAIN”
or “M+R.”
A:
Output to the OUTPUT A (MIX) jacks in stereo.
B:
Output to the OUTPUT B jacks in stereo.
* When Chorus Output Select is set to “REV,” this setting will have no effect.
* If the Mix/Parallel parameter is set to “MIX,” all sounds are output from the OUTPUT A (MIX) jacks in stereo (p. 158).

Reverb Level 0–127 Volume of the sound passed through reverb
Reverb Output
Assign
A, B Specifies how the sound routed through reverb will be output.
A:
Output to the OUTPUT A (MIX) jacks in stereo.
B:
Output to the OUTPUT B jacks in stereo.
* If the Mix/Parallel parameter is set to “MIX,” all sounds are output from the OUTPUT A (MIX) jacks in stereo (p. 158).

Mastering Effect
Type
0–5 Mastering effect settings (p. 156)

Applying Effects in Performance Mode

Specifying How the Sound Will Be Output (Routing)

Parameter Value Explanation

Part Select 1–16 Part for which you want to make settings
Part Output As-
sign
MFX, A, B, 1–4,
PAT
Specifies for each part how the direct sound will be output.
MFX:
Output in stereo through multi-effects. You can also apply chorus or reverb to the sound that passes
through multi-effects.
A, B:
OUTPUT A (MIX) jack or OUTPUT B jack in stereo without passing through multi-effects
1–4:
INDIVIDUAL 1–4 jacks in mono without passing through multi-effects
PAT:
Determined by the settings of the patch or rhythm set assigned to the part.
* If the Mix/Parallel parameter is set to “MIX,” all sounds are output from the OUTPUT A (MIX) jacks in stereo (p. 158).

Part Output
MFX Select
1–3
(MFX1–MFX3)
Specifies which multi-effects will be used.
Part Output Lev-
el
0–127 Level of the signal sent to the output destination specified by Part Output Assign ( )
Part Chorus
Send Level
0–127 Level of the signal sent to chorus for each part
Part Reverb Send
Level
0–127 Level of the signal sent to reverb for each part.

Parameter Value Explanation
12
13
14

15

6
7
8
9
10
11
12
13
14
15
1
2
3
4
5
16
17
7911 14
1
2
3
4 2
5
6
JUNO-G_e.book 127 ページ ２００６年２月１３日　月曜日　午後２時４４分