Roland JUNO-G Creating a Rhythm Set

49
Creating a Rhythm Set
With the JUNO-G, you have total control over a wide variety of
settings. Each item that can be set is known as a parameter . When
you change the values of parameters, you are doing what is referred
to as Editing . This chapter explains the procedures used in creating
rhythm sets, and the functions of the rhythm set parameters.
You can use the six SOUND MODIFY knobs to edit the sound in real
time.
In the case of a sound that has only a brief duration, it may be
difficult to hear the effect of turning a knob.
1.
Press MODE [PATCH] to access the PATCH PLAY screen.
2. Select the rhythm set whose settings you want to edit (p. 26).
You cannot edit the patches in the GM2 group.
3.
Press keys to specify the key (A0–C8) that is to be
controlled by the SOUND MODIFY knobs.
Selecting the tone to edit
4.
In the PATCH PLAY screen, press [TONE SW/SEL] so the
button is lit.
5. Press SELECT[1]–[4] to select the tone(s) you want to edit.
In the SOUND MODIFY 1–4 area at the bottom of the screen, a
check mark ( ✔ ) will be added to the tone number(s) you select.
* You can press multiple buttons simultaneously to select multiple
tones.
* By turning TONE SWITCH on/off you can edit the sound while
hearing only the desired tone.
Changing the brightness of the sound and
adding special qualities (CUTOFF/RESONANCE)
The sound generator section of the JUNO-G contains a filter that can
cut or boost specific frequency regions of the sound. The CUTOFF
knob specifies the frequency (cutoff frequency) at which the filter
will begin to modify the sound, and the RESONANCE knob boosts
the region near the cutoff frequency to add a distinctive character to
the sound.
6.
Turn the CUTOFF or RESONANCE knobs.
Turning a knob toward the right increases the value.
FREQ: Frequency at which the filter begins to have an effect on
the waveform’s frequency components
RESO: Emphasizes the portion of the sound in the region of the
cutoff frequency, adding character to the sound
* Excessively high settings can produce oscillation, causing the sound to
distort.
Editing the way that the volume will change
The volume continues to change from the time a key is pressed to
when it is released.
7.
Press the SOUND MODIFY select button to make AMP ENV
light.
8.
Turn the ATTACK, DECAY, SUSTAIN, and RELEASE knobs.
Turning a knob toward the right increases the value.
A: Attack Time: The time from when the keyboard is pressed
until the maximum tonal change is reached.
D: Delay Time: The time from when the maximum tonal change
is reached until the Sustain Level is reached.
S: Sustain level: Volume that is sustained while you hold down
the key
R: Release Time: The time from when the keyboard is released
until the sound disappears.
* If you press the SOUND MODIFY select button so all of the
indicators are off, turning these knobs will not produce any change.
Editing the way that tone (brightness) will change
The tone undergoes changes between the moment you press a key
until you release it.
9. Press the SOUND MODIFY select button to make FILTER
ENV light.
10.
Turn the ATTACK, DECAY, SUSTAIN, and RELEASE knobs.
Turning a knob toward the right increases the value.
* If you press the SOUND MODIFY select button so all of the
indicators are off, turning these knobs will not produce any change.
The important parameters most commonly used to edit the sound
are available in five screens for graphic editing.
1.
Press MODE [PATCH] to access the PATCH PLAY screen.
2. Select the rhythm set whose settings you want to edit (p. 26).
You cannot edit the patches in the GM2 group.
3.
Press EDIT [PATCH] so it’s lit.
4.
Press keys to specify the key (A0–C8) that is to be edited.
5.
Use [F1]–[F4] to select the parameter screen.
6.
Use [ ] [ ] [ ] [ ] to select a parameter.
* Some parameters can be edited independently for each tone. To select
the tone to edit, press [TONE SW/SEL] so it’s lit, and press one of the
SELECT [1]–[4] buttons.
How to Make Rhythm Set
Settings
Using the Knobs to Edit the Sound
Editing in a Graphic Display
(Zoom Edit)
Parameter page
PITCH ENVELOPE ZOOM p. 54
TVF PARAMETER ZOOM p. 55
TVF ENVELOPE ZOOM p. 55
TVA ENVELOPE ZOOM p. 56
JUNO-G_e.book 49 ページ ２００６年２月１３日 月曜日 午後２時４４分