Manuals / Rose electronic / Computer Equipment / Network Card

Rose electronic Crystal View operation manual Connecting the Cables, Installation

Models: Crystal View

1 52

Download 52 pages 32.79 Kb

Page 25

Step 2: Connecting the Cables

INSTALLATION

Step 2: Connecting the Cables

Power down your PC and connect the appropriate CPU cable to the Keyboard, Video and Mouse ports on the CPU. Connect the other end of the CPU cable to the Local Units Keyboard, Video and Mouse connectors. If the Local Unit is a dual model, make sure you connect the cables to the connectors marked “TO PC”.

(See the CrystalView Cables section and Appendix C. Parts and Cables)

Connect your KVM station’s Keyboard, Video monitor and Mouse cables to the corresponding CrystalView Remote Unit’s Keyboard, Video and Mouse connectors. If your Unit is a Dual version, you can also connect a second KVM station to the Local Unit and access the CPU from either Unit independently but not simultaneously. A lockout feature inhibits the “not-in-use” unit.

For the audio option, connect the “Line In” connector on the Local Unit to the CPUs sound card “Line Out” connector using a standard 3.5mm stereo audio cable. On the Remote Unit, connect a pair of computer speakers or a headset to the “Line Out” connector.

(See Figure 1)

For the Serial option, connect the DB9F serial connector on the Local Unit to the DB9M connector on the CPU using a standard DB9MF cable. Connect the DB9M connector on the Remote Unit to your serial device.

(See Figure 1)

Finally, connect the CAT5 cable to the RJ45 jacks on both the Local and Remote Units.

It is recommended that you test the complete system before permanently installing the Local and Remote units.

19

CrystalView Installation and Operations Manual

Image 25

Rose electronic Crystal View operation manual Connecting the Cables, Installation

Contents

INSTALLATION AND OPERATION MANUAL FOR SERIAL/AUDIO MODEL LIMITED WARRANTY MAC is the trademark of Macintosh Corp LIMITED WARRANTYEUROPEAN UNION DECLARATION OF CONFORMITY FCC/IC STATEMENTS, EU DECLARATION OF CONFORMITYTABLE of CONTENTS ContentsTables FiguresTABLE of CONTENTS AppendixesQUICK START Quick Start GuideStep 1- Set Jumpers QUICK START Step 2 - Connect Local Units CablesQUICK START Step 3 - Connect Remote Units CablesQUICK START Step 4- Connect CAT-5 CableQUICK START Step 5 - Adjust the Video CompensationRemote Unit INTRODUCTION IntroductionINTRODUCTION FeaturesTable 1. Compatibility CompatibilityINTRODUCTION The package contents consists of the following Package ContentsRose Electronics Web Site About this ManualSYSTEM OVERVIEW System OverviewSee Table 3 for the ”Hot Key” summary SYSTEM OVERVIEWSYSTEM OVERVIEW Figure 1. Typical InstallationCrystalView Cables CrystalView ModelsMODELS/CABLES Figure 2. CrystalView Serial/Audio ModelSerial Cables Local Unit to Remote Unit CableAudio Cables CrystalView to Rose switch CableINPUTS/OUTPUTS Figure 3. CrystalView Rear ConnectorsINSTALLATION InstallationStep 1 Setting the Cable Length Jumpers TIP If you are using a cable that is close to the top end of the cable length range and a Video resolution of 1024 x 768 or higher, you may achieve better Video quality by selecting the jumper settings for the next higher cable length range. For example, if your CAT5 cable length is 250 feet, you might achieve better Video quality if you set jumpers JP3, JP4, and JP5 to the 301 - 600 setting. Likewise, if you are at a cable length of 500 feet, a setting of 601 - 1,000 might provide a better Video quality INSTALLATIONINSTALLATION Figure 4. CrystalView Remote PCB w/Daughter boardINSTALLATION Step 2 Connecting the CablesStep 4 Adjusting Video Compensation Step 3 Applying PowerINSTALLATION See Appendix C. Parts and Cables INSTALLATIONINSTALLATION Installing Serial DevicesINSTALLATION Installing Audio DevicesSwitch User Selectable SettingsTable 2. SW1 Switch Setting FunctionINSTALLATION Dual, serial/audio model specific notesOperating Instructions- All Units KVM SwitchingOperating Instructions - Dual Unit OPERATING INSTRUCTIONSOut-of-Sync Mouse Private Mode Dual model onlyRe-initialize Mouse Command Null Mouse CommandReset Keyboard/Mouse Enter Private Mode Dual models onlySend Null Mouse Command Hot Key SummaryTROUBLESHOOTING TroubleshootingPC boots with no error messages but Keyboard does not work PC always comes up with a Keyboard error message at bootPS/2 Mouse cursor appears on the screen, but Mouse does not work TROUBLESHOTINGSystem does not detect PS/2 Mouse or application cannot find Mouse Mouse movement is erraticEach character separates into overlapping red, green and blue pixels Video Picture is not sharp or is smearedOnly Video is required, but no picture appears TROUBLESHOOTINGA constant vertical wobble appears down the screen No sound at the remote units speakers or headphonesPicture on monitor is black and white, not color TROUBLESHOTINGSERVICE INFORMATION Service InformationMaintenance and Repair Technical SupportSAFETY SafetySafety Information Safety and EMC Regulatory StatementsGrounding ServicingSafety and EMC Regulatory Statements SAFETYInformations concernant la sécurité APPENDIXES Appendix A. General SpecificationsAppendix A2. Audio Option Specifications Appendix A1. Serial Option SpecificationsAPPENDIXES Wire Color Appendix B. UTP/STP ConnectionWire Pair APPENDIXESPart Number Appendix C. Parts and CablesDescription APPENDIXESAppendix E. Video Compensation Appendix D. Firmware UpdatesAPPENDIXES APPENDIXES Appendix F. Rack Mount InstructionsAPPENDIXES Appendix G. Rack Mount IllustrationGLOSSARY GlossaryINDEX Index