Manuals / Rose electronic / Computer Equipment / Network Card

Rose electronic Crystal View operation manual Installing Audio Devices, Installation

Models: Crystal View

1 52

Download 52 pages 32.79 Kb

Page 29

Installing Audio Devices

INSTALLATION

Installing Audio Devices

(See Appendix A2. Audio Option Specifications).

CrystalView models with the audio option use two standard 3.5mm stereo jacks on both the Local Unit and Remote Unit. They are labeled “LINE/MIC Out” and “LINE IN” on the Local Unit and “LINE/MIC IN” and “LINE OUT” on the Remote Unit. The “LINE IN” audio jack on the Local Unit is normally connected directly to the “LINE OUT” jack on the CPUs sound card. The “LINE OUT” jack on the Remote Unit usually connects to a pair of computer speakers or headphones.

To connect a microphone to the Remote Unit, connect the “LINE IN” connector on the Remote Unit to the Microphone. Connect the “LINE/MIC OUT” connector on the Local Unit to the “MIC” input on the CPUs sound card. The sound card should be set-up to provide an additional 20db of amplification. See your sound card manual for instructions.

If increasing the microphone amplification on the sound card cannot be done, or your microphone is not a powered microphone, you can use the built-in microphone amplifier located in the Remote Unit. * To set this, open the Remote Unit and locate the jumper labeled “MIC” on the PCB’s daughterboard. Reposition the jumper on the “MIC” jumper block pins to short the two terminals.

(See Figure 4 for location of “MIC” jumper)

* DO NOT install the amplification jumper if your microphone is already amplified.

23

CrystalView Installation and Operations Manual

Image 29

Rose electronic Crystal View operation manual Installing Audio Devices, Installation

Contents

INSTALLATION AND OPERATION MANUAL FOR SERIAL/AUDIO MODEL LIMITED WARRANTY MAC is the trademark of Macintosh Corp LIMITED WARRANTYEUROPEAN UNION DECLARATION OF CONFORMITY FCC/IC STATEMENTS, EU DECLARATION OF CONFORMITYTABLE of CONTENTS ContentsTables FiguresTABLE of CONTENTS AppendixesStep 1- Set Jumpers Quick Start GuideQUICK START QUICK START Step 2 - Connect Local Units CablesQUICK START Step 3 - Connect Remote Units CablesQUICK START Step 4- Connect CAT-5 CableRemote Unit Step 5 - Adjust the Video CompensationQUICK START INTRODUCTION IntroductionINTRODUCTION FeaturesINTRODUCTION CompatibilityTable 1. Compatibility The package contents consists of the following Package ContentsRose Electronics Web Site About this ManualSYSTEM OVERVIEW System OverviewSee Table 3 for the ”Hot Key” summary SYSTEM OVERVIEWSYSTEM OVERVIEW Figure 1. Typical InstallationCrystalView Cables CrystalView ModelsMODELS/CABLES Figure 2. CrystalView Serial/Audio ModelSerial Cables Local Unit to Remote Unit CableAudio Cables CrystalView to Rose switch CableINPUTS/OUTPUTS Figure 3. CrystalView Rear ConnectorsStep 1 Setting the Cable Length Jumpers InstallationINSTALLATION TIP If you are using a cable that is close to the top end of the cable length range and a Video resolution of 1024 x 768 or higher, you may achieve better Video quality by selecting the jumper settings for the next higher cable length range. For example, if your CAT5 cable length is 250 feet, you might achieve better Video quality if you set jumpers JP3, JP4, and JP5 to the 301 - 600 setting. Likewise, if you are at a cable length of 500 feet, a setting of 601 - 1,000 might provide a better Video quality INSTALLATIONINSTALLATION Figure 4. CrystalView Remote PCB w/Daughter boardINSTALLATION Step 2 Connecting the CablesINSTALLATION Step 3 Applying PowerStep 4 Adjusting Video Compensation See Appendix C. Parts and Cables INSTALLATIONINSTALLATION Installing Serial DevicesINSTALLATION Installing Audio DevicesSwitch User Selectable SettingsTable 2. SW1 Switch Setting FunctionINSTALLATION Dual, serial/audio model specific notesOperating Instructions- All Units KVM SwitchingOperating Instructions - Dual Unit OPERATING INSTRUCTIONSOut-of-Sync Mouse Private Mode Dual model onlyRe-initialize Mouse Command Null Mouse CommandSend Null Mouse Command Reset Keyboard/MouseHot Key Summary Enter Private Mode Dual models onlyTROUBLESHOOTING TroubleshootingPC boots with no error messages but Keyboard does not work PC always comes up with a Keyboard error message at bootPS/2 Mouse cursor appears on the screen, but Mouse does not work TROUBLESHOTINGSystem does not detect PS/2 Mouse or application cannot find Mouse Mouse movement is erraticEach character separates into overlapping red, green and blue pixels Video Picture is not sharp or is smearedOnly Video is required, but no picture appears TROUBLESHOOTINGA constant vertical wobble appears down the screen No sound at the remote units speakers or headphonesPicture on monitor is black and white, not color TROUBLESHOTINGSERVICE INFORMATION Service InformationMaintenance and Repair Technical SupportSAFETY SafetySafety Information Safety and EMC Regulatory StatementsGrounding ServicingInformations concernant la sécurité SAFETYSafety and EMC Regulatory Statements APPENDIXES Appendix A. General SpecificationsAPPENDIXES Appendix A1. Serial Option SpecificationsAppendix A2. Audio Option Specifications Wire Color Appendix B. UTP/STP ConnectionWire Pair APPENDIXESPart Number Appendix C. Parts and CablesDescription APPENDIXESAPPENDIXES Appendix D. Firmware UpdatesAppendix E. Video Compensation APPENDIXES Appendix F. Rack Mount InstructionsAPPENDIXES Appendix G. Rack Mount IllustrationGLOSSARY GlossaryINDEX Index