Manuals / Rose electronic / Computer Equipment / Network Card

Rose electronic Crystal View Safety and EMC Regulatory Statements, Safety Information, Grounding

Models: Crystal View

1 52

Download 52 pages 32.79 Kb

Page 41

Safety and EMC Regulatory Statements

SAFETY

Safety and EMC Regulatory Statements

Safety Information

Documentation reference symbol. If the product is marked with this symbol, refer to the product documentation to get more information about the product.

WARNING	A WARNING in the manual denotes a hazard that can
	cause injury or death.
CAUTION	A CAUTION in the manual denotes a hazard that can
	damage equipment.

Do not proceed beyond a WARNING or CAUTION notice until you have understood the hazardous conditions and have taken appropriate steps.

Grounding

These are Safety Class I products and have protective earthing terminals. There must be an un-interruptible safety earth ground from the main power source to the product’s input wiring terminals, power cord, or supplied power cord set. Whenever it is likely that the protection has been impaired, disconnect the power cord until the ground has been restored.

Servicing

There are no user-serviceable parts inside these products. Only service-trained personnel must perform any servicing, maintenance, or repair.

Only items mentioned in this manual may be adjusted by the user.

35

CrystalView Installation and Operations Manual

Image 41

Rose electronic Crystal View Safety and EMC Regulatory Statements, Safety Information, Grounding, Servicing

Contents

INSTALLATION AND OPERATION MANUAL FOR SERIAL/AUDIO MODEL LIMITED WARRANTY MAC is the trademark of Macintosh Corp LIMITED WARRANTYEUROPEAN UNION DECLARATION OF CONFORMITY FCC/IC STATEMENTS, EU DECLARATION OF CONFORMITYTABLE of CONTENTS ContentsTables FiguresTABLE of CONTENTS AppendixesStep 1- Set Jumpers Quick Start GuideQUICK START QUICK START Step 2 - Connect Local Units CablesQUICK START Step 3 - Connect Remote Units CablesQUICK START Step 4- Connect CAT-5 CableRemote Unit Step 5 - Adjust the Video CompensationQUICK START INTRODUCTION IntroductionINTRODUCTION FeaturesINTRODUCTION CompatibilityTable 1. Compatibility The package contents consists of the following Package ContentsRose Electronics Web Site About this ManualSYSTEM OVERVIEW System OverviewSee Table 3 for the ”Hot Key” summary SYSTEM OVERVIEWSYSTEM OVERVIEW Figure 1. Typical InstallationCrystalView Cables CrystalView ModelsMODELS/CABLES Figure 2. CrystalView Serial/Audio ModelSerial Cables Local Unit to Remote Unit CableAudio Cables CrystalView to Rose switch CableINPUTS/OUTPUTS Figure 3. CrystalView Rear ConnectorsStep 1 Setting the Cable Length Jumpers InstallationINSTALLATION TIP If you are using a cable that is close to the top end of the cable length range and a Video resolution of 1024 x 768 or higher, you may achieve better Video quality by selecting the jumper settings for the next higher cable length range. For example, if your CAT5 cable length is 250 feet, you might achieve better Video quality if you set jumpers JP3, JP4, and JP5 to the 301 - 600 setting. Likewise, if you are at a cable length of 500 feet, a setting of 601 - 1,000 might provide a better Video quality INSTALLATIONINSTALLATION Figure 4. CrystalView Remote PCB w/Daughter boardINSTALLATION Step 2 Connecting the CablesINSTALLATION Step 3 Applying PowerStep 4 Adjusting Video Compensation See Appendix C. Parts and Cables INSTALLATIONINSTALLATION Installing Serial DevicesINSTALLATION Installing Audio DevicesSwitch User Selectable SettingsTable 2. SW1 Switch Setting FunctionINSTALLATION Dual, serial/audio model specific notesOperating Instructions- All Units KVM SwitchingOperating Instructions - Dual Unit OPERATING INSTRUCTIONSOut-of-Sync Mouse Private Mode Dual model onlyRe-initialize Mouse Command Null Mouse CommandReset Keyboard/Mouse Enter Private Mode Dual models onlySend Null Mouse Command Hot Key SummaryTROUBLESHOOTING TroubleshootingPC boots with no error messages but Keyboard does not work PC always comes up with a Keyboard error message at bootPS/2 Mouse cursor appears on the screen, but Mouse does not work TROUBLESHOTINGSystem does not detect PS/2 Mouse or application cannot find Mouse Mouse movement is erraticEach character separates into overlapping red, green and blue pixels Video Picture is not sharp or is smearedOnly Video is required, but no picture appears TROUBLESHOOTINGA constant vertical wobble appears down the screen No sound at the remote units speakers or headphonesPicture on monitor is black and white, not color TROUBLESHOTINGSERVICE INFORMATION Service InformationMaintenance and Repair Technical SupportSAFETY SafetySafety Information Safety and EMC Regulatory StatementsGrounding ServicingInformations concernant la sécurité SAFETYSafety and EMC Regulatory Statements APPENDIXES Appendix A. General SpecificationsAPPENDIXES Appendix A1. Serial Option SpecificationsAppendix A2. Audio Option Specifications Wire Color Appendix B. UTP/STP ConnectionWire Pair APPENDIXESPart Number Appendix C. Parts and CablesDescription APPENDIXESAPPENDIXES Appendix D. Firmware UpdatesAppendix E. Video Compensation APPENDIXES Appendix F. Rack Mount InstructionsAPPENDIXES Appendix G. Rack Mount IllustrationGLOSSARY GlossaryINDEX Index