Manuals / Runco / Computer Equipment / Projector

Runco CL-810 ULTRA manual 1. Troubleshooting Chart continued, Maintenance and Troubleshooting

Models: CL-810 / SDC-1 CL-810 ULTRA CL-810 CINEWIDE

1 92

Download 92 pages 44.57 Kb

Page 79

Image 79

Maintenance and Troubleshooting

Table 5-1. Troubleshooting Chart (continued)

Symptom

TEMP and LAMP LEDs are both flashing red.

LAMP LED lights solid red.

TEMP LED lights solid red.

Possible Cause(s)

•The lamp cover is open.

•Fans are not working properly.

•The lamp has failed or exceeded its usage life.

•CL-810 internal temperature is too high.

Solution

•Close the lamp cover.

•Please contact your Runco dealer for assistance.

•Replace the lamp with a new one.

•Power off the CL-810 and allow it to cool down. Ensure that the intake and exhaust vents are not blocked. Turn the projector back on. If the problem persists, please contact your Runco dealer for assistance.

Runco CL-810 Series Owner’s Operating Manual

Page 79

Image 79

Runco CL-810 ULTRA, CL-810 CINEWIDE, CL-810 / SDC-1 1. Troubleshooting Chart continued, Maintenance and Troubleshooting

Contents

OW N E R ’S OP E R A T I N G MA N U A L Digital Light ProcessingTM Projectors CL-810 CL-810 UltraCL-810 CineWide CL-810 / SDC-1 CL-810 SeriesPage For Projectors, Video Processors and Controllers TWO YEAR LIMITED WARRANTYWHAT IS COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY WHAT IS NOT COVERED UNDER THE TERMS OF THIS LIMITED WARRANTYCOPYRIGHT AND TRADEMARKS EFFECTIVE WARRANTY DATEIMPORTANT - WARRANTY REGISTRATION CONTACT A RUNCO AUTHORIZED SERVICE CENTER TO OBTAIN SERVICEADDITIONAL INFORMATION RUNCO INTERNATIONAL, INC Attn Customer Service Department2900 Faber Street Union City, CA Ph 510 Fax 510 Toll Free 800 23-RUNCOSafety Precautions Installation Table of ContentsTWO YEAR LIMITED WARRANTY Safety PrecautionsMounting the CL-810 Table of Contents Maintenance and TroubleshootingLamp Replacement SpecificationsRunco CL-810 Series Owner’s Operating Manual Table of Contents3-7. CL-810 Ultra with Lens Motor Mounting Plate and Ceiling Mount List of FiguresRunco CL-810 Series Owner’s Operating Manual Runco CL-810 Series Owner’s Operating Manual List of FiguresTarget Audience A carriage return must be used after each command or stringIntroduction About This Manual1.3 Related Documents 1.2 Using This Manualcertain features DANGER appears when a given action can cause severe injury orformat screen 1.4 Description, Features and BenefitsOptional Accessories - CL-810 Ultra Only Optional Accessories - CL-810 and CL-810 Ultra2. PROJECTION LENS 3. TOP IR SENSOR 4. TEMP LED 2. Controls and Functions2.1 CL-810 at a Glance Figure 2-1. CL-810 Front/Side/Top View 1. RUNCO LOGO8. EXHAUST VENT 9. FRONT IR SENSOR 6. POWER/STANDBY LED Indicates power status as follows3. CABLE ACCESS DOOR Open to access connectors 7. LAMP LED6. CEILING MOUNT HOLES 5. FRONT/REAR ADJUSTERS2.2 CL-810 Rear Panel 4. LAMP MODULE COVERFor best results, do not run your DVD player in progressive mode 3. COMP 1 RCA connectors6. POWER INPUT 100 to 240 VAC Connect the CL-810 to power here 7. MAIN POWER SWITCHRunco CL-810 Series Owner’s Operating Manual 2.3 CL-810 Remote ControlFigure 2-4. CL-810 Remote Control Controls and Functions3. Source Selection Buttons VID RVR Reflectance Volume Regulation1. LIGHT 2. ON / OFFCOL Color 5. Picture Adjustment Buttons BRT Brightness6. Memory Preset Buttons MEM1 CONT Contrast10. Motorized Lens Controls FOCUS 9. Picture-In-Picture PIP / Picture-By-Picture PBP ControlsSDC-1 System Expansion Device PIP+3.1 Remote Control InstallationNotes on Batteries Notes on Remote Control Operation installation specialist 3.2 Quick SetupTable 3-1. Installation Overview Installation should be performed by a qualified custom videoAmbient Light 3.3 Installation ConsiderationsTable 3-2. Projector Installation Options Installation TypeFigure 3-1. Estimating Throw Distance Table 3-3. CL-810 Ultra Lens Options and Throw Ratios Vertical and Horizontal Ceiling InstallationFloor Installation Figure 3-2. Projector PlacementRunco CL-810 Series Owner’s Operating Manual Figure 3-4. Horizontal Lens Shift EXAMPLE ONLYInstallation lens or projector is used in this exampleInstallation Table 3-4. Vertical and Horizontal Lens Shift LimitsFigure 3-5. Folded Optics Folded OpticsOther Considerations 1. Do not install the CineWide lens yet, only the AutoScope lens Mounting Plate and Install Lens MotorRemove Projector Front FeetDO NOT OVER-TIGHTEN THE SCREWS Figure 3-8. AutoScope Lens Motor InstallationFloor Mounting Upright projector. Install the mount kit according to the instructionsAdjusting the Projector 3.5 Mounting the CL-810CL-810 Connector Panel AccessFigure 3-9. Connecting the CL-810 to the SDC-1 Connections to theFigure 3-11. RGB Connections Connecting Source Components to the CL-810Use the HDMI input whenever possible. This ensures the highest Figure 3-10. HDMI/DVI Source ConnectionsY Pb Pr Figure 3-12. Progressive Component Video ConnectionsInstallation Runco CL-810 Series Owner’s Operating ManualRunco CL-810 Series Owner’s Operating Manual DTV Source DVD Player, VCR Satellite Receiver etcFigure 3-13. Composite, S-Video and Component Video Connections InstallationConnection RS-232 ControllerFigure 3-14. RS-232 Control System Connection Figure 3-16. Connecting the 12-Volt Trigger Output to Other Equipment Connecting 12-Volt Trigger Output to External Theater EquipmentAutoScope Lens Motor Rear The input voltage to the AutoScope lens motor must be between 3.7 Turning on the PowerFocus 3.8 Changing the OSD Language 3.9 Adjusting the Picture OrientationPrimary Lens Adjustments 3.10It is extremely important that the primary lens is properly 3.11 Installing and Adjusting the CineWide Anamorphic LensAnamorphic Lens Installation and Adjustment - CL-810 Ultra/CineWide with AutoScopeFigure 3-18. Attaching the Anamorphic Lens to the Lens Ring Attaching Lens Mounting Assembly to Lens Motor Carriage PlateToo Far Left Correct position Too Far Right Adjusting the Horizontal X Lens PositionToo Low Correct position Too High There may be some pincushion distortion even after the lens isGeometry Anamorphic Lens Top ViewAnamorphic Lens Too Low Correct position Too High Adjusting the Lens Height YAdjustment 8 Pitch Adjustment Yoke for Lens 9 Anamorphic LensPitch Adjustment T-Screw 4 T-Screw Long 5 Height Y-Adjustment T-ScrewAdjusting the Lens Height Y Geometry Runco CL-810 Series Owner’s Operating Manual Installation4.1 Selecting Video Memory 4.2 Selecting an Aspect Ratio 4.3 Adjusting the PicturePicture Adjustment on page OperationGraphic HD group HDMI and Component 2/RGB inputs 4.5 Using Picture-In-Picture/ Picture-By-Picture PIP/PBP4.6 Using the On-Screen Menus Video SD group Video, S-Video and Component 1 inputsS-Video InstallationSet Up VideoMain Menu Picture AdjustmentWhen you change a picture quality setting, save the change to a preset afterwards. Otherwise, the change will be lost when aFigure 4-2. Typical PLUGE Pattern for Adjusting Brightness cyan Figure 4-3. Typical Gray Bar Pattern for Adjusting Contrastgray yellowgreen grayyellow cyanbelow is set to Figure 4-5. Typical Test Pattern for Adjusting SharpnessAspect Ratio You must enter a passcode in order to enter the Set Up menuWhen you change the aspect ratio, save the change to a preset The International Color Consortium ICC is a group of imagingOperation Table 4-1. Aspect Ratio SettingsCinema Table 4-1. Aspect Ratio Settings continuedOperation Runco CL-810 Series Owner’s Operating ManualOSD Timer Use the InstallationWhen you change a setting in the Installation menu, the change Runco recommends that the keystone feature not be used unlessor button to adjust Shift controls in the Set Up menu see pageENTER You only need to enter the Set Up menu passcode the first time Set Upyou select that menu after turning on the projector Use the on-screen slidebar to select the desired amount of over scan 1. To adjust the image position with a 480p or higher-resolution7.5 IRE Used for most NTSC video signals order to change the secondary IR codeIf your CL-810 Ultra installation includes an SDC-1 System source ONLY, press the button to highlight “Yes” then press ENTER When you change a setting, save the change to a presetISF Calibration This menu should be used by ISF-certified technicians onlySplash Screen Timer Use the or button to set the Splash Screen Timer. This timer controls how long the startup ISF and Runco logo image stays on-screen after you turn on the projector. Select from 5 to 60 seconds, in 1-second increments. When finished, press EXIT Runco CL-810 Series Owner’s Operating Manual Operation5.1 Lamp Replacement Maintenance and Troubleshootingthe lamp assembly for replacement Table 5-1. Troubleshooting Chart 5.2 Troubleshooting TipsMaintenance and Troubleshooting Maintenance and Troubleshooting Table 5-1. Troubleshooting Chart continuedRunco CL-810 Series Owner’s Operating Manual Runco CL-810 Series Owner’s Operating Manual Maintenance and TroubleshootingSerial Communications 6.1 RS-232 Connection and Port Configuration 6.2Serial Command Syntax Table 6-1. Serial CommandsSerial Communications Table 6-1. Serial Commands continuedRunco CL-810 Series Owner’s Operating Manual Table 6-1. Serial Commands continuedSerial Communications x081xRunco CL-810 Series Owner’s Operating Manual Serial CommunicationsRunco CL-810 Series Owner’s Operating Manual SpecificationsCL-810 Specifications Table 7-1. CL-810 SpecificationsSpecifications Table 7-1. CL-810 Specifications continuedRunco CL-810 Series Owner’s Operating Manual Table 7-1. CL-810 Specifications continuedSpecifications Weight without lensRunco CL-810 Series Owner’s Operating Manual 7.2 CL-810 DimensionsFigure 7-1. CL-810 Dimensions SpecificationsRunco CL-810 Series Owner’s Operating Manual 7.3 CL-810 Ultra DimensionsFigure 7-2. CL-810 Ultra Dimensions SpecificationsRunco CL-810 Series Owner’s Operating Manual SpecificationsPage RUMA-011135 rev 04-23-07 Runco CL-810 Owner’s Operating ManualSERIAL NUMBER