Memory Presets | Runco CX-70DHD instruction

Operation

For each input, the CX-70DHD lets you save image quality settings as presets that you can recall at a later time. You can create up to four presets per input and display mode (resolution and frame rate).

The DHD Controller stores the following display modes in each memory preset:

•480i

•480p

•576i

•576p

•720p/24 Hz

•720p/25 Hz

•720p/30 Hz

•720p/50 Hz

•720p/60 Hz

•1080i/50 Hz

•1080i/50 Hz (Australia)

•1080i/60 Hz

•1080p/24 Hz

•1080p/25 Hz

•1080p/30 Hz

•1080p/50 Hz

•1080p/60 Hz

Use the Memory Presets menu to recall saved image presets, or to save image settings in the “Custom 1” or “Custom 2” memory location. The currently-selected preset is indicated by a “➡” to its left; in the example shown here, ISF Night is selected.

You should save changes to any of the following settings to a preset; otherwise they will be lost when a new input source or resolution is selected:

•Brightness

•Contrast

•Color saturation

•Tint

•Sharpness

•Gamma

•Lamp Settings

•Color temperature and white balance

To select a memory preset, press or to highlight it and press ENTER.

To save the settings for the current input and display mode to the Custom 1 or Custom 2 memory preset, select it, press or to highlight Save and press ENTER.

To save the settings for the current input and display mode to the

Note ISF Night or ISF Day memory preset, select Save ISF Night or Save ISF Day from the Calibration menu (refer to Save ISF Night/Save ISF Day on page 50).

Memory Presets

Memory Presets

➡ISF Night ISF Day

Custom 1	Save	Reset
Custom 2	Save	Reset

CX-70DHD Installation/Operation Manual

47

Image 61

Runco CX-70DHD operation manual Memory Presets

Contents

CX-70DHD Page RuncoCare Standard Features RuncoCare Standard Two Year Limited Warranty RuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance Information FCC Part Industry Canada ICES-003 Page Table of Contents Specifications Maintenance and TroubleshootingOperation External Control List of Figures List of Figures Xiv About This Manual Introduction If you need Turn to Using This Manual Key Features and Benefits Description, Features and Benefits Optional Accessories Controls and Functions Controls and IndicatorsCX-70DHD at a Glance STANDBY/ON Indicator Power SwitchRemote Control Sensor Display Stand DHD Controller Front Panel Down Button Left ButtonRight Button Menu Button Triggers DHD Controller Rear PanelInputs 10. IR Main Power SwitchRS-232 / RS-485 Main AC Fuse DHD Controller/CX-70DHD Remote Control CX-70DHD Remote Control Unit Enter IR Output IndicatorReturn / Exit Light SVC CinemaISF Night ISF DAY Controls and Functions Remote Control Installation Installation Overview Quick SetupStep Procedure For Details, refer to Synchronization Issues Installation ConsiderationsAmbient Light Ventilation Input Timing Possible Audio Latency milliseconds Possible Audio Latency for Various Input/Output Timings On a Wall or Table Stand Mounting the CX-70DHD Qty Description Assembling and Installing the Table Stand Connections to the CX-70DHD and DHD Controller Connecting CX-70DHD to the DHD Controller Connecting the CX-70DHD to the DHD Controller Sections that follow Connecting SourceComponents to the DHD Hdmi Source Connections See Figure Hdmi Source Connections DTV-Set-Top Box BD/DVD DTV-STB Rgbhv Source Connections Computer RGB Camcorder DVD/DTV STB VCRGaming Console Camcorder Composite and S-Video Source Connections Connection RS-232 Controller 12. Connecting 12-volt Trigger Outputs Connecting 12-volt 13. External IR Receiver Connection Connecting an External IR Receiver to the DHD Controller Installation Operation Turning on the Power Setting the Computer Display Properties Operation Using the On-Screen Menus Main Menu ServiceRunco Video Aspect Ratio Input SourceInput Source Aspect Ratio Remote Aspect Ratio Control Description Key 169 Aspect Ratio SettingsSelect 169 to view 169 DVDs Hdtv programs in their Overscan Remote Aspect Ratio Control Description Key Picture Picture Typical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Input Position Input Position Adjust the Phase after adjusting Tracking see below Memory Presets Memory Presets Calibration InformationShould be used by ISF-certified technicians only CIE 1931 Chromaticity Diagram Color Temperature Preset Associated x/y Values Color Temperature Presets and Associated Color Points Copy/Paste Copied settings are not retained after a power cycle Service ServiceInput Names Exit Operation 47 and ISF Day/Night Memory Presets Operation Cleaning Maintenance and TroubleshootingTroubleshooting Tips Troubleshooting Chart To Input Position on Serial Command Syntax Port ConfigurationExternal Control Serial Communications Input Selection Commands Serial Commands Picture Adjust Commands Output Shift Commands Input Position Commands Exit Return key Enter key Command Bits Using Discrete IR CodesWith Toggle Bit = Hex Binary Function Start Remote Control With Toggle Description Button Name Bit = IR Command ListRC5 Control Codes for the DHD Controller RC5 Data Enter CX-70DHD Specifications SpecificationsCX-70DHD Specifications DHD Controller Specifications DHD Controller Specifications CX-70DHD Dimensions with Table Stand CX-70DHD Dimensions Format Resolution Frequency Rate Hz MHz KHz Supported Signal Timings by InputSupported Timings Supported? √ = Yes, = No PAL-B/G/H/I PAL-M Page 020-0925-01 Rev. B April