Gray Yellow Cyan Green Magenta Red Blue | Runco CX-70DHD instruction

Operation

Color Saturation: On your external test pattern source, select a color bar pattern like the one shown in Figure 4-4.

gray

yellow

cyan

green

magenta

red

blue

Figure 4-4. Typical Color Bar Pattern for Adjusting Color Saturation and Tint

1.Press the MENU button on the remote control or DHD Controller front panel.

2.Select Service from the Main Menu and press ENTER.

3.Enter the Service menu passcode.

4.Select Display Device from the Service menu and press ENTER.

5.Press ENTER again to select Configure.

6.Select Diagnostics and press ENTER.

7.Select Blue from the Diagnostics menu, then press ENTER to display only the blue color channel.

8.Press RETURN (or MENU) repeatedly to return to the Main Menu.

9.Select Picture from the Main Menu and press ENTER.

10.Select Color from the Picture menu and press ENTER.

42	CX-70DHD Installation/Operation Manual

Image 56

Runco CX-70DHD operation manual Gray Yellow Cyan Green Magenta Red Blue

Contents

CX-70DHD Page RuncoCare Standard Two Year Limited Warranty RuncoCare Standard Features RuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of Conformity FCC Part Industry Canada ICES-003 Page Table of Contents Maintenance and Troubleshooting SpecificationsOperation External Control List of Figures List of Figures Xiv Introduction About This Manual Using This Manual If you need Turn to Description, Features and Benefits Key Features and Benefits Optional Accessories CX-70DHD at a Glance Controls and IndicatorsControls and Functions Power Switch STANDBY/ON IndicatorRemote Control Sensor Display Stand DHD Controller Front Panel Left Button Down ButtonRight Button Menu Button Inputs DHD Controller Rear PanelTriggers Main Power Switch 10. IRRS-232 / RS-485 Main AC Fuse CX-70DHD Remote Control Unit DHD Controller/CX-70DHD Remote Control IR Output Indicator EnterReturn / Exit Light Cinema SVCISF Night ISF DAY Controls and Functions Installation Remote Control Step Procedure For Details, refer to Quick SetupInstallation Overview Installation Considerations Synchronization IssuesAmbient Light Ventilation Possible Audio Latency for Various Input/Output Timings Input Timing Possible Audio Latency milliseconds Mounting the CX-70DHD On a Wall or Table Stand Assembling and Installing the Table Stand Qty Description Connecting CX-70DHD to the DHD Controller Connections to the CX-70DHD and DHD Controller Connecting the CX-70DHD to the DHD Controller Connecting Source Sections that followComponents to the DHD Hdmi Source Connections See Figure Hdmi Source Connections BD/DVD DTV-STB DTV-Set-Top Box Computer RGB Camcorder Rgbhv Source Connections Gaming Console VCRDVD/DTV STB Composite and S-Video Source Connections Camcorder RS-232 Controller Connection Connecting 12-volt 12. Connecting 12-volt Trigger Outputs Connecting an External IR Receiver to the DHD Controller 13. External IR Receiver Connection Installation Turning on the Power Setting the Computer Display Properties Operation Operation Using the On-Screen Menus Runco Video ServiceMain Menu Input Source Aspect RatioInput Source Aspect Ratio Aspect Ratio Settings Remote Aspect Ratio Control Description Key 169Select 169 to view 169 DVDs Hdtv programs in their Remote Aspect Ratio Control Description Key Overscan Picture Picture Typical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Input Position Input Position Adjust the Phase after adjusting Tracking see below Memory Presets Memory Presets Should be used by ISF-certified technicians only InformationCalibration CIE 1931 Chromaticity Diagram Color Temperature Presets and Associated Color Points Color Temperature Preset Associated x/y Values Copied settings are not retained after a power cycle Copy/Paste Input Names ServiceService Exit Operation 47 and ISF Day/Night Memory Presets Operation Maintenance and Troubleshooting CleaningTroubleshooting Tips Troubleshooting Chart To Input Position on Port Configuration Serial Command SyntaxExternal Control Serial Communications Serial Commands Input Selection Commands Picture Adjust Commands Input Position Commands Output Shift Commands Enter key Exit Return key With Toggle Bit = Hex Binary Function Start Using Discrete IR CodesCommand Bits IR Command List Remote Control With Toggle Description Button Name Bit =RC5 Control Codes for the DHD Controller RC5 Data Enter CX-70DHD Specifications SpecificationsCX-70DHD Specifications DHD Controller Specifications DHD Controller Specifications CX-70DHD Dimensions CX-70DHD Dimensions with Table Stand Supported Signal Timings by Input Format Resolution Frequency Rate Hz MHz KHzSupported Timings Supported? √ = Yes, = No PAL-B/G/H/I PAL-M Page 020-0925-01 Rev. B April