Manuals / Samsung / TV and Video / Projection Television

Samsung HL-R5688W manual Remove the 2 press-pin 3 screws securing the Lamp

Models: HL-R5688W

1 144

Download 144 pages 58.64 Kb

Page 139

Image 139

• For replacement, you will need a 5.91-Inch screwdriver and a pair of gloves.

Unplug TV, then use a

1 screwdriver to remove the screws.

2 Remove the Lamp cover.

Remove the 2 press-pin

3 screws securing the Lamp.

Separate the Lamp from the

4 engine by holding the handle and pulling it out.

To reinstall the Lamp, follow

5 these steps in reverse order.

NOTES

•Be sure the replacement Lamp is the same type.

•After replacing the lamp, align the lamp cover with the groove and secure the screws.

•The TV will not turn on if the lamp cover is not correctly closed (as this will activate the protective circuit).

English - 139

Page 139

Image 139

Samsung HL-R5688W manual Remove the 2 press-pin 3 screws securing the Lamp

Contents

HL-R5688W Owner’s InstructionsThis device is a Class B digital apparatus License Notice Trademark NoticeEnglish Digital Picture Quality Digital Television ServicesA Guide to Digital TV What is Digital Television?CableCARD and Digital Cable Ready TVs 4. Can I connect my DTV set-top receiver to my cable TV service? 2. How difficult is it to receive DTV signals indoors?5. I hear a Clicking sound in standby mode Operation Table of ContentsYour New Wide TV ConnectionsDigital AnalogAppendix S A M S U N G Your New Wide TV Viewing Position Your New Wide TVAccessories List of FeaturesYour New Wide TV Front Panel ButtonsWhen these indicators appear, there is a possible problem with the TV Front Panel Information WindowYour New Wide TV Rear Panel JacksRemote Control Your New Wide TV Installing Batteries in the Remote ControlConnections Connections Connecting VHF and UHF AntennasAntennas with 75-ohm Round Leads Cable without a Cable Box Connecting Cable TVCable with a Cable Box that Descrambles All Channels Connections Connecting a VCRConnecting a VCR to the Video or S-Video/Audio jack Alternate methodConnecting CableCARD Connections Connecting a CamcorderOutput Jacks Connecting to Y, PB, PR Connecting a DVD PlayerConnections Connecting a DTV Set-Top BoxConnecting to Y, PB, PR Connecting to DVI Digital Visual InterfaceConnecting to HDMI High Definition Multimedia Interface TV Rear Panel Connecting a VCR and DTV Set-Top BoxConnecting to an Analog Amplifier Connecting a Digital Audio SystemConnections Connecting to a Subwoofer Speaker S A M S U N G Operation Viewing the Menus OperationTurning the TV On and Off Viewing the Menus and On-Screen DisplaysSelecting a Menu Language Memorizing the Channels Selecting the Video Signal SourceOperation Channel When the Cable card is inserted, you do not need to save channelsIn Memory Adding and Erasing ChannelsOperation Not In MemoryUsing the Previous Channel Using the Channel ButtonsUsing the Number Buttons Using the “-” ButtonOperation Customizing Your Remote ControlSetting Up Your Remote Control to Operate Your VCR Cable box or DVD playerVCR Codes Cable Box Codes DVD Codes Remote Control CodesOption 1 Setting the Clock Manually Setting the ClockOperation Sound Central Mountain Option 2 Setting the Clock AutomaticallyManual AtlanticAuto Power Off Setting the On/Off TimerOperation Minute Setting the Sleep TimerAlternate method Viewing an External Signal SourceSetting the Signal Source OperationAssigning Names to External Input Mode S A M S U N G Channel Control To View Your Favorite Channels Channel ControlSelecting Your Favorite Channels To Store Your Favorite ChannelsAlternate method Viewing the Channel ListsChannel Control Adding and Erasing ChannelsMore Channel Labeling the ChannelsName The LNA setting must be made separately for each channel LNA Low Noise AmplifierLNA functions only when antenna is set to Air The settings will be stored separately in each channelAnalog Fine Tuning Analog ChannelsDigital Checking the Digital-Signal StrengthChannel Control Picture Control Picture Control Picture ControlThe Tint cannot be adjusted while watching Digital TV Customizing the Picture Settings“Tint” doesn’t operate in HDMI or 480p Component or higher modes Picture Control Resetting the Picture Settings to the Factory DefaultsColor tone is not available in the “Movie” picture mode Zoom1 Zoom2 Changing the Picture SizeAlternate method 169 PanoramaPicture Control Digital Noise ReductionDigital NR Alternate method Viewing the DNIe DemonstrationDNIeTM Digital Natural Image engine Using the My Color Control Function in the Easy Control Menu Setting the My Color Control ModePicture Control My Color Control Custom Settings Picture Control Using the Color Weakness Enhancement FeatureColor Weakness Film mode is supported in 480i only Setting the Film ModePicture Control Viewing Picture-In-PictureActivating the PIP This feature doesn’t function when the “V-Chip” is activeSource Selecting an External SourceSWAP is not available when the Main picture is a Digital broadcast Swapping the Sub PIP Picture and Main PicturePicture Control Size Changing the Size of the Sub PIP PicturePicture Control Changing the Location of the Sub PIP PictureThe Double , mode cannot be selected in Position Selecting a Signal Source Antenna or Cable for PIP Channel Changing the Channel of the Sub PIP PicturePicture Control Alternate methodSound Select Selecting the Sound SourcePress again to cancel Freezing the PicturePicture Control Blue Screen Setting the Blue Screen ModeS A M S U N G Sound Control Sound Control Adjusting the VolumeUsing the MUTE Button Sound ControlL/R Sound Balance Adjustment Using Automatic Sound SettingsSound Control Setting the SRS TSXTSRS TSXT Auto Volume Auto VolumeAlternate method Choosing a Multi-Channel Sound MTS trackSound Control DigitalChoose “Stereo” for channels that are broadcasting in stereo AnalogChoosing a Multi-Channel Sound MTS track Alternate methodDigital Output Choosing a Digital Sound FormatSound Control DigitalSound Selecting the Internal MuteMain Setting the On/Off MelodySound Control Sound SelectRefer to page 27 for SubWoofer connection Setting up the SubWoofer OutputS A M S U N G Special Features Setup Special FeaturesSetting the Function Help SetupSetup Menu Transparency LevelSetup SetupSpecial Features Using the V-ChipHow to Change Your Password V-Chip Lock How to Enable/Disable the Rating ControlsSpecial Features How to Set up Restrictions Using the “TV Parental Guidelines”Allow All Press to unlock all TV ratings Block All Press to lock all movie ratings How to Set up Restrictions Using the “MPAA Rating”Special Features Allow All Press to unlock all movie ratingsMPAA Rating System Movies TV FCC Content CategoryImportant Notes About Parental Locks TV FCC Age-Based RatingsSpecial Features How to Set up Restrictions Using Canadian EnglishCanadian English Special Features How to Set up Restrictions Using Canadian FrenchAllow All Block All Canadian FrenchCaption Special FeaturesAnalog Viewing Closed Captions On-Screen Text MessagesThe default is “CC1” Digital Special FeaturesDefault On Viewing Closed Captions On-Screen Text MessagesFont Style Return to DefaultAlternate method SizeSpecial Features Setting the Port Selection ModeDisplaying CableCARD related information Using the CableCARDCableCARD Reset Using the CableCARD Setup FunctionSpecial Features Channel List Reorganization Special Features Using Game ModeDisabled Menus in Game Mode Restrictions on Game Mode CautionTurning the TV On and Off Using TV Guide On ScreenTMReminder Screen Special Features Using TV Guide On ScreenTM continuedListings Using the D-Net How to connect compatible IEEE1394 Devices Using the D-NetWhat’s D-Net? When Connecting D-Net IEEE1394 Compatible devices Using the D-Net Connection OptionsThe Direct Device-To-Device Option The Hub Connection Option4-Pin and 6-Pin Connectors Using the D-Net Selecting a D-Net deviceThis is also available using the D-Net button on the remote control Follow the instructions below to activate D-Net in the menu1 Press the MENU button Press the ENTER button to select “Input” Using the D-Net The D-Net control panelControl Panel Using the D-Net Operating TipsMessage Copy informationDescriptions Tips on stopping recording Recording TipsUsing the D-Net Problem Troubleshooting D-NetUsing the D-Net Possible SolutionProblem Problem Problem Using the D-NetThis device is unavailable for D-Net PC Display PC Display Using Your TV as a Computer PC DisplayHow to Connect Your PC to the TV Connecting a PC 15p D-SUB to the TVSetting up Your PC Software Windows only Setting the Display Modes to be Compatible with Your TV Checklist Before Connecting to a PCPC Display Channel Adjusting the Picture QualityListings PC Display Changing the Picture PositionAdjusting the Picture Quality and Position Automatically WidePC Changing the Picture Size PC ModePC Display Alternate methodTo change the resolution, see pages 129~130 Viewing the Current ResolutionPC Display Initializing the Picture SettingsAppendix Appendix PIP SettingsReplacing the Lamp Remove the 2 press-pin 3 screws securing the Lamp Appendix TroubleshootingProblem Possible SolutionI want to view the clearest picture on the TV in 1080p resolution ProblemPlacement Cleaning and Maintaining Your TVUsing Your TV in Another Country SpecificationsPage Samsung Electronics Canada Inc. Samsung Customer Care 1-800-SAMSUNG Samsung Electronics America Service DivisionBP68-00489A-03