Sanyo E11A202U 15.4 Specifications

15.4 Specifications

	Item			Standard or Performance			Notes
	MODEL			E11A202U001		E11A202U001J	(*6)
	Output capacity			2.0kVA/1.4kW
	Cooling system			Forced air cooling
	Type of Input pulg			NEMA 5-20P		NEMA L5-30P	(*6) When the plug is NEMA_5-20, the
							input and output voltage of UPS are
							120V. only (For UL rules.)
	Phases			Single phase, 2-wire
AC				120V		100,110,115,120V
	Voltage			-20% to +15% Double Conversion mode			User settable
input
				±5% Economy /Active Filter mode
							(Rated voltage same as output voltage)
				±10% Fixed Economy mode
	Frequency			50Hz or 60Hz			±10%: Double Conversion mode
							±1, 3, 5%: Economy /Active Filter mode
	Power requirements				1.8kVA		Max. capacity during battery charging
	Input power factor			0.95 or more			During rated output	(*2)
	Type of receptacle			NEMA 5-20R×4		NEMA L5-30R×1
	Phases			Single phase, 2-wire
	Voltage			120V		100, 110, 115, 120V	(*6) User settable
	Voltage regulation			Rated voltage ±2%
	Rated frequency			50Hz or 60Hz			Same as input frequency
							(auto selection)
				Rated frequency ±0.5% Double Conversion mode			1, 3, 5% selectable
	Frequency regulation			Rated frequency ±1, 3, 5% Economy/Active Filter			Internal oscillator accuracy ±0.5%
						mode
	Voltage waveform			Sine wave
AC	Distortion factor of voltage			Linear load: 3% or less			During rated output
	waveform			100% rectifier load: 7% or less
Output
			Rapid load				0% ⇔ 100% at transient or output
	Transient		change				switch
		Power outage,		Rated voltage			During rated output
	voltage		recovery
	variation				±5 %
			Rapid input				±10% variation
		voltage change
	Response time			5 cycles or less
	Load power factor (lag)			0.7 (lag)			Variation range 0.7 (lag) to 1.0
	Overcurrent protection			Auto switch to bypass circuit at 105% or more			With auto return function
	Overload		Inverter		105%		200ms
	capability		Bypass	20A or more
Batteries			Type	Small sealed lead battery
	Rated capacity				10 A･h		At 25°C (77°F) ambient temperature,
							20 hour ratio
	Number			4 (12V per battery)			4 in direct series
	Backup time			5 minutes			rated load
	Generated heat				250W		During Double Conversion mode
	Input leakage current			3mA or less
	Operating environment			Ambient temperature: 0 to 40°C (32 to 104°F)			(*3)
				Relative humidity: 20 to 90%
	Acoustic noise			45 dB or less			1 m (approx. 40 inches) from UPS front
							panel, 'A' characteristics (linear load)
	Safety standard			UL1778-4th/C22.2 No.107.3-05-2nd:2005
	EMI standard			FCC Part 15,Sub partB,Class-A			And EN55022 Class-A
				EN62040-1-1:2003 (For LVD)
Other quotation standards				EN50091-2:1995 (For EMC)
				EN55024:1998/A1:2001/A2:2003 (For EMC)
				EN55022:1994/A1:1995/A2:1997 (For EMC)

(*1): The inverter is capable of operation synchronized with AC input and instantaneous switchover provided that the AC input frequency is within ±3% (or 1%, 3%, 5%, selectable) of the rated frequency, and the AC input voltage is within +15% to-20% of the rated voltage.

The UPS enters battery operation with the AC input frequency is outside the specified range. (*2): When input voltage waveform distortion is under 1%.

(*3): The UPS contains batteries. Battery service life will be foreshortened if the UPS is used in an environment where the ambient temperature exceeds 30°C (86°F).

(*4): If grounded, the ground phase of the input and output must match according to UPS specifications.

*****continues to the following page.*****

− 40 −