Manuals / Schneider Electric / Computer Equipment / Computer Hardware

Schneider Electric 890USE19600 Version 1.0 manual STB NIB 1010 Module Specifications

Models: 890USE19600 Version 1.0 INTERBUS Basic Network Interface Module

1 71

Download 71 pages 16.46 Kb

Page 28

Image 28

The STB NIB 1010 Basic NIM Module

STB NIB 1010 Module Specifications

Table of

Technical

Specifications

dimensions	width	40.5 mm (1.59 in)

	height	130 mm (5.12 in)

	depth	70 mm (3.15 in)

interface connectors	from INTERBUS network	nine-pin SUB-D connector (male)

	to INTERBUS network	nine-pin SUB-D connector (female)

	RS-232 port for	8-receptacle HE-13
	configuration software or
	HMI panel

	to external 24 VDC power	2-receptacle
	supply

built-in power supply	input voltage	24 VDC nominal

	input power range	19.2 ... 30 VDC

	input current	400 mA @ 24 VDC

	output voltage to island	5 VDC @ 1.2 A
	bus
	bus	2% variation due to temperature drift, intolerance, or line
		2% variation due to temperature drift, intolerance, or line
		regulation

		1% load regulation

		<50 mΩ output impedance up to 100 kHz

	output current rating	5 VDC @ 1.2 A

	isolation	no internal isolation (isolation must be provided by a SELV-rated
		external 24 VDC source power supply)

	noise immunity (EMC)	IEC 1131-2

addressable I/O modules supported		12 maximum

segments supported		one

hot swapping		no

standards	INTERBUS conformance	INTERBUS Club (www.interbusclub.com)

MTBF		200,000 hours GB (ground benign)

28	890USE19600 April 2004

Image 28

Schneider Electric 890USE19600 Version 1.0 manual STB NIB 1010 Module Specifications, Technical Specifications

Contents

Advantys STB 890USE19600 VersionPage Table of Contents Application Example Procedure Safety InformationImportant Information Safety Information About the Book At a GlanceValidity Note Construed as a commitment by Schneider Electric About the Book Summary What’s in this Chapter? IntroductionTopic What Is Advantys STB? IntroductionIsland Bus I/O Basic What Is a Network Interface Module? Structural Outputs in 4 ms About InterbusComponents of a simplified Interbus network are shown below Physical Layer Topology Node AddressingInput and output data in the masters buffer On the shift register ring on which data is circulated Introduction Product specifications of the basic Interbus NIM STB NIB Basic NIM ModuleWhat’s in this Chapter? External Features of the STB NIB 1010 NIM Features Called out in the illustration belowFeature Function Hardware Space reserved for the network connectors NIM housing STB NIB 1010 Fieldbus Interface SummaryFieldbus Port Connections Connectors InterbusNetworking Cable LED Physical Description OverviewGeneral Indications NIM Activity LEDs Power Supply Interface Island is the two-receptacle connector illustrated belowPhysical Description Use either Right Logic Power Improper Galvanic Isolation Characteristics Power SupplyRequirements External STB NIB 1010 Module Specifications Technical Specifications Configuring the Island Bus Basic island configuration Auto-AddressingAbout the Island Bus Address An Example Module Physical Location Island Bus Address Configuration Auto-ConfigurationAbout Auto Been successfully configured at least once RST ButtonHinged cover Stage Island Fallback Scenarios FallbackScenarios Heartbeat Fieldbus Communications Support Introduction What’s in this Chapter? Interbus ID Code LowHigh Bytes Data Type Data Length Data Exchange Data and StatusObjects Objects Internal Process ImageWord Boundaries Output Data Input DataExchange Contains the NIM status Application Example With an Advantys STB NIB 1010 basic NIM Sample Island Assembly AssemblyFieldbus network Sample Island I/O modules have the following island bus addresses Model Module Type Island Bus Address Network Configuration Considerations For use with an Advantys STB islandConnection Devices on an Interbus network Before You BeginSyCon Considerations Using SyCon to Configure an STB Island on Interbus With SyConStage Description Step Action Comment To add the NIM to the network configuration ConfiguringAdd the NIM Workspace Create an EDS Instructions Saving Island slave to your configuration using CMD Using CMD to Configure an STB Island on InterbusCMD Add AddingIsland Slave Downloading Application Example Glossary ARP BOS Can COBComs CRC Dhcp DINEDS EIA EMC EMIEOS Fedp Fsdp GSD Base ScanningIEC IEC type 1 input Industrial I/O Input filteringInput polarity Input response Energized and open when the coil is energized Energized and closed when the coil is energizedContact Nema NIM NMT PDO PDMPLC Process I/O ProducerConsumer model Profibus DP RTD SAPScada SDO Smmps Snmp TCP StdpTFE UDP VaristorSuppress transient voltage surges Voltage group Index Heartbeat message, 34 housing ID code Interbus Index