Manuals / Schneider Electric / Computer Equipment / Computer Hardware

Schneider Electric 890USE19600 Version 1.0 manual LED Physical Description, Overview, General

Models: 890USE19600 Version 1.0 INTERBUS Basic Network Interface Module

1 71

Download 71 pages 16.46 Kb

Page 22

The STB NIB 1010 Basic NIM Module

LED Physical Description

Overview	The six LEDs implemented in the STB NIB 1010 INTERBUS NIM are visual
	indications of the operating status of the island bus on an INTERBUS network. The
	LED array is located at the top of the NIM front bezel.

General	The bottom three LEDs indicate the status of data exchange between the
Indications	INTERBUS fieldbus master and the Advantys island bus:
	LED 4—RC (remote bus check)
	LED 5—BA (bus active)
	LED 6—RD (remote bus disabled)
	The top three LEDs indicate activity or events on the NIM:
	LED 1—RUN
	LED 2—PWR/UL
	LED 3—ERR
	The following tables describe the LED behavior in more detail. When you refer to
	these tables, keep in mind:
	It is assumed that the PWR/UL LED is on continuously, indicating that the NIM is
	receiving adequate power. If the PWR/UL LED is off, logic power to the NIM is off
	or insufficient.
	Individual blinks are approximately 200 ms. There is a 1-second interval between
	blink sequences. For example:
	blinking—blinks steadily, alternating between 200 ms on and 200 ms off
	blink 1—blinks once (200 ms), then 1 second off
	blink 2—blinks twice (200 ms on, 200 ms off, 200 ms on), then 1 second off
	blink n—blinks n (some number) times, then 1 second off

22	890USE19600 April 2004

Image 22

Schneider Electric 890USE19600 Version 1.0 manual LED Physical Description, Overview, General, Indications

Contents

Advantys STB 890USE19600 VersionPage Table of Contents Application Example Procedure Safety InformationImportant Information Safety Information Validity Note About the BookAt a Glance Construed as a commitment by Schneider Electric About the Book Summary What’s in this Chapter? IntroductionTopic Island Bus I/O What Is Advantys STB?Introduction Basic What Is a Network Interface Module? Structural Outputs in 4 ms About InterbusComponents of a simplified Interbus network are shown below Physical Layer Topology Input and output data in the masters buffer NodeAddressing On the shift register ring on which data is circulated Introduction What’s in this Product specifications of the basic Interbus NIMSTB NIB Basic NIM Module Chapter? Feature Function External Features of the STB NIB 1010 NIMFeatures Called out in the illustration below Hardware Space reserved for the network connectors NIM housing Fieldbus Port STB NIB 1010 Fieldbus InterfaceSummary Connections Networking ConnectorsInterbus Cable General LED Physical DescriptionOverview Indications NIM Activity LEDs Physical Power Supply InterfaceIsland is the two-receptacle connector illustrated below Description Use either Right Logic Power Improper Galvanic Isolation Requirements CharacteristicsPower Supply External STB NIB 1010 Module Specifications Technical Specifications Configuring the Island Bus About the Island Basic island configurationAuto-Addressing Bus Address An Example Module Physical Location Island Bus Address Configuration Auto-ConfigurationAbout Auto Hinged cover Been successfully configured at least onceRST Button Stage Scenarios Island Fallback ScenariosFallback Heartbeat Fieldbus Communications Support Introduction What’s in this Chapter? High Bytes Interbus ID CodeLow Data Type Data Length Objects Data ExchangeData and Status Objects Word InternalProcess Image Boundaries Exchange Output DataInput Data Contains the NIM status Application Example With an Advantys STB NIB 1010 basic NIM Fieldbus network Sample Island AssemblyAssembly Sample Island I/O modules have the following island bus addresses Model Module Type Island Bus Address Connection Network Configuration ConsiderationsFor use with an Advantys STB island Devices on an Interbus network SyCon Before YouBegin Considerations Stage Description Using SyCon to Configure an STB Island on InterbusWith SyCon Step Action Comment Add the NIM To add the NIM to the network configurationConfiguring Workspace Create an EDS Instructions Saving Island slave to your configuration using CMD Using CMD to Configure an STB Island on InterbusCMD Island Slave AddAdding Downloading Application Example Glossary ARP BOS Coms CanCOB CRC EDS DhcpDIN EIA EOS EMCEMI Fedp Fsdp GSD IEC BaseScanning IEC type 1 input Input polarity Industrial I/OInput filtering Input response Contact Energized and open when the coil is energizedEnergized and closed when the coil is energized Nema NIM NMT PDO PDMPLC Consumer model Process I/OProducer Profibus DP Scada RTDSAP SDO Smmps Snmp TCP StdpTFE Suppress transient voltage surges UDPVaristor Voltage group Index Heartbeat message, 34 housing ID code Interbus Index