Manuals / Schneider Electric / Computer Equipment / Computer Hardware

Schneider Electric INTERBUS Basic Network Interface Module, 890USE19600 Version 1.0 manual

Models: 890USE19600 Version 1.0 INTERBUS Basic Network Interface Module

1 71

Download 71 pages 16.46 Kb

Page 57

Manual background

	Glossary

EMC	electromagnetic compatibility. Devices that meet EMC requirements can operate
	within a system’s expected electromagnetic limits without error.
EMI	electromagnetic interference. EMI can cause an interruption, malfunction, or
	disturbance in the performance of electronic equipment. It occurs when a source
	electronically transmits a signal that interferes with other equipment.
EOS	end of segment. When more than one segment of I/O modules is used in an island,
	an STB XBE 1000 EOS module is installed in the last position in every segment that
	has an extension following it. The EOS module extends island bus communications
	to the next segment.
Ethernet	A LAN cabling and signaling specification used to connect devices within a defined
	area, e.g., a building. Ethernet uses a bus or a star topology to connect different
	nodes on a network.0
Ethernet II	A frame format in which the header specifies the packet type, Ethernet II is the
	default frame format for STB NIP 2212 communications.

F

fallback state	A safe state to which an Advantys STB I/O module can return in the event that its
	communication connection fails.
fallback value	The value that a device assumes during fallback. Typically, the fallback value is
	either configurable or the last stored value for the device.
FED_P	Fipio extended device profile. On a Fipio network, the standard device profile type
	for agents whose data length is more than eight words and equal to or less than
	thirty-two words.
Fipio	Fieldbus Interface Protocol (FIP). An open fieldbus standard and protocol that
	conforms to the FIP/World FIP standard. Fipio is designed to provide low-level
	configuration, parameterization, data exchange, and diagnostic services.
Flash memory	Flash memory is nonvolatile memory that can be overwritten. It is stored on a special
	EEPROM that can be erased and reprogrammed.
FRD_P	Fipio reduced device profile. On a Fipio network, the standard device profile type for
	agents whose data length is two words or less.

890USE19600 April 2004

57

Image 57

Schneider Electric INTERBUS Basic Network Interface Module, 890USE19600 Version 1.0 manual

Contents

Advantys STB INTERBUS Basic Network Interface Module Applications Guide31005789 Page Safety Information About the Book Chapter 1 Introduction Table of ContentsChapter 3 Configuring the Island Bus Chapter 2 The STB NIB 1010 Basic NIM ModuleChapter 5 Application Example Safety Information Important InformationDANGER 2004 Schneider Electric. All Rights Reserved At a Glance About the BookAbout the Book At a Glance IntroductionSummary What’s in this Chapter? 890USE19600 AprilIntroduction What Is Advantys STB?Island Bus I/O The BasicIntegrated Power What Is a Network Interface Module?Purpose The FieldbusStructural Overviewnetwork view and a physical representation of the island bus the network ring sometimes this last device has no out connector About INTERBUSoutputs in 4 ms Components of a simplified INTERBUS network are shown belowPage Addressing Node890USE19600 April IntroductionThe STB NIB Basic NIM ModuleAt a Glance Features External Features of the STB NIB 1010 NIMHardware called out in the illustration below1 space reserved for the network connectors 2 NIM housing The STB NIB 1010 Basic NIM Module890USE19600 April Summary STB NIB 1010 Fieldbus InterfaceFieldbus Port Connectionsuse of reserved pins Connectorsring is closed INTERBUSLED Physical Description LEDs NIM ActivityPower Supply Interface Use either power and sends it across the basic segment Logic Powerthe modules in the basic segment voltage SELV-ratedSelecting a Source Power Supply for the Island’s Logic Power Bus Table of Technical Specifications STB NIB 1010 Module SpecificationsAuto-Configuration Configuring the Island BusAt a Glance Auto-AddressingAuto-Addressing Module An ExamplePhysical Location Island Bus AddressAuto-Configuration The RST Button Island Fallback Scenarios Support Fieldbus CommunicationsAt a Glance Introduction What’s in this Chapter?The INTERBUS ID Code Actual Length of Island Data Data LengthINTERBUS Data Length Data Length Code HexData Exchange Data and StatusObjects The STB NIB 1010’s process image contains memory areas buffers for the contains the NIM status At a Glance Application ExampleSample Island Assembly the fieldbus networkvariety of analog and digital modules I/O Model The I/O modules have the following island bus addressesModule Type Island Bus AddressNetwork Configuration Considerations bits with SyCon Using SyCon to Configure an STB Island on INTERBUSConfiguring in To add the NIM to the network configurationmaster and INTERBUS NIM slave to your network configuration, a SyCon Add the NIMYou can create an EDS using SyCons EDS Generator by following these Create an EDSinstructions 890USE19600 April Using CMD to Configure an STB Island on INTERBUS specific device when a configured one is not available Controller Board to your configuration projectyour configuration The Advantys island is always configured as a remote890USE19600 April Application ExampleGlossary Page Page Page Page HTTP hot swappingFSDP full scaleI/O base IEEEI/O module I/O scanninglinearity light industrialmandatory MAC addressmodule master/slavePage Page Page Page state managementmessage periodic services. The applications and network Page voltage group varistorIndex