Sears 113.20765 manual Unpacking and checking contents

contents

POWER TOOL WARRANTY								...................		2
GENERAL SAFETY				INSTRUCTIONS
FOR POWER TOOLS							...........................			2
ADDITIONAL		SAFETY				INSTRUCTIONS
FOR SCROLL			SAW			..............................				3
MOTOR SPECIFICATIONS								AND
ELECTRICAL			REQUIREMENTS							4
UNPACKING AND CHECKING CONTENTS ,, 5
ASSEMBLY
Assembling		Steel		Legs				........................		6
Mounting		Scroll		Saw		on		Leg Set		7
Mounting		Scroll		Saw		to		Workbench		7
Mounting Scroll Saw to Mounting Board .... 8
Adjusting		Guard		...........................						8
Installing		Miter	Lock			Knob			.....................	8
Blade Installation				and			Tensioning
for	Plain-End		and		Pin		Type		Blades	9
To	Install/Tension				Plain			End	Blades	9
Adjusting		Insert		To	Table					t0
To	Install/Tension				Pin		Type		Blades	tl
To Remove Plain-End							or Pin Type Blades.,			11
Adjusting		the Blade Square to Table								13
Installation		of	Bevel			Scales				14

GETTING TO KNOW YOUR SCROLL SAW
Tension Control			Knob	15
Guard	Lock	Knobs		15
Guard	......................................			15
Blower	Tube	..................................		15
Blade	Holder	Retaining Clips		15
Blade	Holders		................................	15
Blade	Holder	Pockets		15
Miter	Gauge	Lock Knob		15
Table	Insert	................................		15
Blade	Storage		...................................	15
Bevel	Lock Knob			!5
Bevel	Scales	..................................		15
On-Off	Switch		..................................	15
Blade	Storage		..................................	16
BASIC SCROLL			SAW OPERATION
Sawing/Scrolling			.............................	17
Bevel	Setting/Cutting			17
Use of Miter		Gauge-Crosscutting		18
Use of Miter		Gauge-Ripping		18
MAINTENANCE			..................................	18
RECOMMENDED			ACCESSORIES	19
TROUBLESHOOTING				19
REPAIR PARTS			................................	20

unpacking and checking contents

	TOOLS	NEEDED
_1	COMBINATION SQUARE
	7/16"	WRENCH	MEDIUM	SCREWDRIVER
	3/4" WRENCH		COMBINATION	SQUARE MUST BE TRUE

Model 113 207600 Scroll Saw is shipped complete in one carton but DOES NOT INCLUDE Steel Legs

Model 113,,207650 Scroll Saw is shipped complete in one carton and INCLUDES Steel Legs

Separate all parts from packing materials and check each item with illustration and "Table of Loose

Parts", Make certain all items are accounted for before discarding any packing material

If any parts are missing, do not attempt to assemble the Scroll Saw, plug in the power cord, or turn the switch on until the missing parts are obtained and installed correctly

Wipe the base with a clean, dry cloth

WARNING: FOR YOUR OWN SAFETY, NEVER CONNECT PLUG TO POWER SOURCE OUTLET UNTIL ALL ASSEMBLY STEPS ARE COMPLETE, AND YOU HAVE READ AND UNDERSTAND THE SAFETY AND OPERATIONAL INSTRUCTIONS,.

1

5

2

3

		_.	STRAtGHT	EDGE OF
DRAW	LIGHT	A	BOARD 314' THICK
		_'"		BE
LINE ON 8CARD
			PERFECTLY	STRAIGHT
ALONG	THIS EDGE

SHOULD BE NO GAP OR OVERLAP HERE WHEN

SQUARE IS FLIPPED OVER IN DOTTED POSITION

Item	Table 0f Loose Parts		Qty.
1	Scroll	Saw	1
_2	Blade	Pack (containing 3 blades)	!
3	Miter	Gauge	!
4	Owner's Manual		1

5Bag Assembly Part #66031 ............

Containing the following parts:

Holder,	Blade		.....................	4
Clip, Blade				4
Key, Switch				1
Knob	.................................			1
Wedge, Rip Fence				1
A Blade Holder			Key	2
Wrench,		Hex "L"3f32		1
A Scale,	Bevel		.........................	2
Insert,	Table		............................	I
Screw	Soc Set t0-32 x 1/4			4
Washer	13/64		x 5/8 x 1/32	t
*Nuts, Hex 1t4-20				4
*L0ckwasher			1/4	4
*Bolts,	Carriage 1/4-20 x 2-1/2			4
*Bumper,		Rubber		4
*Washer		17164 x 314 x 1t16		4

Z_C0ntained in separate bag inside loose parts bag #66031

"Moun_ing Hardware for workbench or mounting board