FULL ONE YEAR WARRANTY ON CRAFTSMAN SCROLL SAW
If within one year from the date of purchase, this Craftsman Scroll Saw fails due to a defect in material or workmanship, Sears will repair it, free of charge+
WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS
SERVICE CENTER/DEPARTMENT THROUGHOUT THE UNITED STATES
This warranty applies only while this product is in use in the United States
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state
SEARS, ROEBUCK AND CO+, 698/731A, Sears Tower, Chicago, IL 60684
general safety instructions for power tooms
1+ KNOW YOUR POWER TOOL
Read and understand the owner's manual and labels affixed to the tool Learn its application and limitations as welf as the specific potential hazards peculiar to this tool+
2,, GROUND ALL TOOLS
This tool is equipped with an approved
3+ KEEP GUARDS IN PLACE
-in working order, and in proper adjustment and alignment.
4+ REMOVE ADJUSTING KEYS AND WRENCHES Form a habit of,checking to see that keys and adjusting wrenches are removed from tool before turning it on.
5.KEEP WORK AREA CLEAN
Cluttered areas and benches invite accidents Floor must not be slippery due to wax or sawdust.
+AVOID DANGEROUS ENVIRONMENT
Don'tuse power tools in damp or wet locations or ex- pose them to rain_ Keep work area well lighted. Pro- vide adequate surrounding work space+
7+ KEEP CHILDREN AWAY
All visitors should be kept a safe distance from work alea+
+ MAKE WORKSHOP KID+PROOF
--with padlocks, master switches, or by removing starter keys
94 DON'T FORCE TOOL
It will do the job better and safer at the rate for which
it was designed+
10+ USE RIGHT TOOL
Don'tforce tool or attachment to do a job it was not designed for,
11+ WEAR PROPER APPAREL
Do not wear loose clothing, gloves, neckties or jewelry
(rings, wristwatches) to get caught in moving parts+ NONSLtP footwear is recommended, Wear protective
hair covering to contain tong hair, Roll long sleeves above the elbow..
12+ USE SAFETY GOGGLES (Head Protection)
Wear safety goggles (must comply with ANSi Z87+1) at all times "Everyday eyeglasses only have impact re+
sistant lenses, they are NOT safety glasses." Also, use face or dust mask if cutting operation is dusty, and ear protectors (plugs or muffs) during extended periods of operation+
13+ SECURE WORK
Use clamps or a vise to hold work when practical tt's safer than using your hands and frees both hands to operate tool
14+ DON'T OVERREACH
Keep proper footing and balance at all times+
15_ MAINTAIN TOOLS WITH CARE
Keep tools sharp and clean for best and safest per- formance. Follow instructions for lubricating and changing accessories+
16.DISCONNECT TOOLS
before servicing; when changing accessories such as blades, bits, cutters, etc
17+ AVOID ACCIDENTAL STARTING
Make sure switch is in"OFF" position before plugging in power cord,,
18.USE RECOMMENDED ACCESSORIES
Consult the owner's manual for recommended acces+ sories+ FoIIow the instructions that accompany the ac-
cessories The use of improper accessoriesmay cause hazards,
19.NEVER STAND ON TOOL
Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted,,
Do not store materials above or near the tool such that it is necessary to stand on the tool to reach them.
20_ CHECK DAMAGED PARTS
Before further use of the tool, a guard or other part that is damaged should be carefully checked to ensure
that it will operate properly and perform its intended function+ Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly re- paired or replaced.
21.DIRECTION OF FEED
Feed work into a blade or cutter against the direction of rotation of the blade or cutter only_
22+ NEVER LEAVE TOOL RUNNING UNATTENDED
Turn power off. Don't leave tool until it comes to a complete stop+
