Screws yet, Tighten the two M6 x 12mm Screws | Sears 23897 guide

	6. Note: The Leveling Foot (41) may be	6
	preattached.	6
	preattached.
	With the help of a second person, place some of
	the packaging materials (not shown) under the
	Frame (1). Have the second person hold the
	Frame to prevent it from tipping while you
	complete this step.	1

Tighten the Leveling Foot (41) into the underside of the Frame (1).

		41
7. Identify the Right Pedal (14) and the Right Pedal	7
Arm (12) assembly and orient them as shown.	7
Arm (12) assembly and orient them as shown.
Attach the Right Pedal (14) to the Right Pedal
Arm (12) with two M6 x 12mm Screws (139) and
two M6 x 13mm Washers (140); do not tighten	14
the Screws yet.	14
the Screws yet.
Next, tighten two M6 x 50mm Screws (62) with
two M6 x 13mm Washers (140) into the Right
Pedal Arm (12) and the Right Pedal (14). Then,
tighten the two M6 x 12mm Screws (139).	12	140
Attach the Left Pedal (not shown) to the Left		140
Attach the Left Pedal (not shown) to the Left	62
Pedal Arm (not shown) assembly in the same	62
way.	140	139
		139
	62

9

Image 9

Sears 23897 user manual Screws yet, Tighten the two M6 x 12mm Screws

Contents

QUESTIONS? Model No Serial NoCall TOLL-FREE Table of Contents Important Precautions Before YOU Begin Part Identification Chart Assembly Wire with the wire tie Tip Avoid pinching the Upright Wire Upright WireAvoid pinching Screws yet Do not press the Top Cover 23 into place yet Avoid damaging Tip Avoid damaging the Upright Wire Tighten the two M6 x 12mm Screws Screws yet See the lower drawing. Pull upward on See the upper drawing. Locate the Ramp 111 Wires Tip Avoid pinching the wires. Attach the RearRepeat this step on the other side Elliptical Repeat this step on the other side of the elliptical See the inset drawing. Locate the Pulse Wire Avoid pinching Wires HOW to Plug in the Power Cord HOW to USE the EllipticalPage HOW to Level the Elliptical HOW to Exercise on the Elliptical Features of the Console Console Diagram HOW to USE the Manual Mode HOW to Turn on the PowerSelect the manual mode Follow your progress with the display Heart rate monitor see page 26 for information Measure your heart rate if desiredAbout the optional chest heart rate monitor Same time, the console will not display your Turn on the fan if desired When you are finished exercising, unplug the power cord HOW to USE AN Onboard Workout Select an onboard workoutBegin pedaling to start the workout Set a calories, distance, or time goal HOW to USE a SET-A-GOAL Workout Make sure that the iFit module is inserted in the console HOW to USE AN Ifit WorkoutSelect a user Select an iFit workout Start the workout. See on HOW to USE the Sound System Follow your progress with the display. See onOptional Chest Heart Rate Monitor HOW to Change Console Settings FCC Information HOW to Adjust the Reed Switch Maintenance and TroubleshootingHeart Rate Monitor Troubleshooting HOW to Calibrate the Ramp HOW to Adjust the Drive Belt Exercise Intensity Exercise GuidelinesWorkout Guidelines Exercise Frequency Suggested Stretches Page Description Qty Part List Qty Description Exploded Drawing a Exploded Drawing Drawing C Exploded 126 102 Ordering Replacement Parts Limited WarrantyIcon Health & Fitness, Inc., 1500 S W., Logan, UT