Adjusting the Resolution and Contrast | Sharp FO-B1600 specs

Adjusting the Resolution and Contrast

Adjusting the Resolution and Contrast

If desired, you can adjust the resolution and contrast before sending a document.

The default resolution setting is STANDARD and the default contrast setting is AUTO.

You must adjust the settings each time you don’t want to use the default settings.

Note: The resolution and contrast settings are only effective for sending a document. They are not effective for receiving a document.

Resolution settings

STANDARD	Use STANDARD for ordinary documents. This
	setting gives you the fastest and most
	economical transmission.
FINE	Use FINE for documents containing small letters
	or fine drawings.
SUPER FINE	Use SUPER FINE for documents containing
	very small letters or very fine drawings.
HALF TONE	Use HALF TONE for photographs and
	illustrations. The original will be reproduced in
	64 shades of gray.
Contrast settings
AUTO	Use AUTO for normal documents.
DARK	Use DARK for faint documents.

36

Image 38

Sharp FO-B1600 operation manual Adjusting the Resolution and Contrast, Resolution settings, Contrast settings

Contents

FO-B1600 About the Telephone Consumer Protection ACT Introduction Vertical Paper tray capacity Applicable telephone line Important safety information Page Table of Contents Printing Lists Maintenance Look at the Operation Panel COPY/HELP key Speaker keyHold key Stop key Installation Unpacking Checklist Removing the packing tape Points to keep in mind when setting upAttachments Open the print compartment cover Connecting the handset Close the printer cover Attaching the paper trays Installation1 Loading Printing Paper Place Connecting the Power Cord Installing the Print Cartridge Open the operation panel Remove only the tape from the the new cartridge Change Cartridge Press NEW if the cartridge you Installed is newPress OLD if the cartridge you Installed is old Press Memory Setting the paper size Press Once Times Ink save modePress Press To turn on ink save mode, or Connecting the Telephone Line Cord Connect the extension phone line to the TEL. SET jack Extension phone optionalRemove the seal covering the TEL. SET jack Entering Your Name and Fax Number Enter your fax number by pressing the number keys max digits Setting the Date and Time Press once and 3 times Daylight Saving Time Mode Setting the Reception ModeSetting the reception mode Speaker Volume AdjustmentDesired volume level Press To select Ringer When talking through the handset Press To selectHandset If you selected Ringer OFF OK ? to Transmittable Documents Size and weightSending Faxes Loading the Document Other restrictions Removing a document from the feeder Open the operation panel Remove the document Contrast settings Adjusting the Resolution and ContrastResolution settings Press RESOLUTION/ one or more times Load the documents Changing the default resolution Sending a Fax by Normal Dialing Sending a Fax by Automatic Dialing Sending a Fax by Automatic Dialing Press Function once Once Storing fax and phone numbers for automatic dialingRapid Keys If you know the Speed Dial number that Memory Date and time display Editing and clearing auto-dial numbersReturn to to store another number, or press to return to Press 1 for Edit or 2 for Clear Press Memory Make the desired changes to the name To the date and time display Load the documents If desired, press Using a Rapid Key for a voice callRapid Key Dialing Memory . If not, press Repeat Step Using a Speed Dial number for a voice callSpeed Dialing Display if no name was stored, the number will appear Searching for an auto-dial numberPress Until the name of the other party appears Sending a fax by Direct Keypad Dialing Correct, press Memory Once. Redial appears in the display, followed by RedialAutomatic redialing Press Redial Error Correction Mode Press Function once Times. Display Batch Page Numbering Sending a Fax From Memory Broadcasting sending a fax to multiple destinations Load the documents If desired, press RESOLUTION/ to set Broadcasting using a Group KeyWhen you are ready to begin transmission, press Memory Press the appropriate Group Key Press To clear a Group Key Storing numbers in Group KeysPress To program a Group Key Press to return to the date and time display Memory transmission If the memory becomes full Changing the number of rings Using FAX ModeReceiving Faxes Using TEL Mode Using TEL Mode Answering on an extension phone connected to the same line Answer the extension phone when it ringsAnswering with the fax’s handset Display shows Receiving and then Press once and 7 times Optional Reception SettingsFax Signal Receive Changing the number for remote fax activation Press To select AUTO, or 2 to Reception RatioPress Function once and twice Select 100% Substitute Reception to Memory Example of two Copies each Three originals Select any of the following copy settings as neededMaking Copies If Memory is Full appears When you are ready to begin copying, pressCopy Cut-off Press Once Twice Connecting an Answering Machine Answering Machine Connection Changing the outgoing message Using the Answering Machine ConnectionSet the reception mode to A.M Set your answering machine to auto answer Quiet Detect Time Optional A.M. Mode SettingsHow answering machine mode operates Enter a number from 01 to 10, or enter To turn off the function Press once and 6 times Quiet Detect Start TimePress Function once On TAD Failure Caller ID Requires Subscription to Service Special Functions Enter the three digits of your area code How Caller ID operatesDisplay messages Press Memory to store your area code Press Z twice Voice call Press when you have finished viewing the listViewing the Caller ID list Fax To store or clear the number To delete calls from the Caller ID listPriority Call Blocking voice calls Distinctive Ring Requires Subscription to Service Set the reception mode to FAX Blocking Reception of Unwanted Faxes Polling Requesting a Fax Transmission Requesting transmission Being polled polling standby Polling security Storing fax numbers for polling permission Enter the fax number maximum of 20 digits Editing and clearing polling permission numbers Press Function once and once Printing ListsActivity Report Press Memory to print the list Group List Setup ListTelephone Number List Caller-ID List Transaction Report Headings in the Transaction Report Transaction Report print condition Auto print-out of Activity Report Press 1 to turn on auto print out, or To turn it off Cleaning the scanning glass and rollers MaintenanceCleaning the Machine Maintenance Cleaning the housing Rotating the white roller Improving Print Quality Aligning the print cartridge Cleaning the print cartridge nozzles Maintenance Wiping the print nozzles and contacts Cleaning the cartridge holder Line error TroubleshootingProblems and Solutions Problem Solution Dialing and transmission problems Trouble- shooting Reception and copying problems 100 General problems Answering machine connection Messages and Signals Press Start KEY 104 Audible signals Recalling Clearing Paper Jams Clearing a jammed document Clearing jammed printing paper Flip down the green levers on each side of the white roller 108 FCC Regulatory Information A R P Material Safety Data Sheet 2/3 Material Safety Data Sheet 3/3 Quick Reference Guide Sending Faxes Guía de referencia rápida Transmisión de documentos Index 115 116 Page Sharp Corporation