Memory transmission, If the memory becomes full | Sharp FO-B1600

Sending a Fax From Memory

Memory transmission

You can also send a fax through memory when sending to a single destination. This is convenient when sending to destinations where the line is often busy, as it saves you from waiting to pick up the original document and frees the feeder for other operations.

To send a fax through memory, load the document, press

dial using one of the following methods:

START/

MEMORY , and then

♦ Press the number keys to enter the fax number and then press			START/
			MEMORY .
		START/
♦ Press a Rapid Key and then press MEMORY .
♦ Press			START/
	SPEED DIAL , enter a 2-digit Speed Dial number, and press		MEMORY .
♦ Press			START/
		repeatedly to select an auto-dial number and then press MEMORY .
	Z	once to select the last number dialed and then press
♦ Press REDIAL

START/

MEMORY .

If the memory becomes full...

If the memory becomes full while the document is being scanned, MEMORY IS FULL will appear in the display.

♦ Press	START/
	MEMORY	if you want to transmit the pages which have been stored up

to that point in memory. The remaining pages will be ejected from the feeder. After transmission, the memory will be cleared and you can transmit the remaining pages. You will also need to transmit the page which was being scanned when the memory filled up.

♦Press if you want to cancel the entire transmission.

STOP

56

Image 58

Sharp FO-B1600 operation manual Memory transmission, If the memory becomes full

Contents

FO-B1600 About the Telephone Consumer Protection ACT Introduction Vertical Paper tray capacity Applicable telephone line Important safety information Page Table of Contents Printing Lists Maintenance Look at the Operation Panel COPY/HELP key Speaker keyHold key Stop key Installation Unpacking Checklist Removing the packing tape Points to keep in mind when setting upAttachments Open the print compartment cover Connecting the handset Close the printer cover Attaching the paper trays Installation1 Loading Printing Paper Place Connecting the Power Cord Installing the Print Cartridge Open the operation panel Remove only the tape from the the new cartridge Change Cartridge Press OLD if the cartridge you Installed is old Installed is newPress NEW if the cartridge you Press Memory Setting the paper size Press Once Times Ink save modePress Press To turn on ink save mode, or Connecting the Telephone Line Cord Remove the seal covering the TEL. SET jack Extension phone optionalConnect the extension phone line to the TEL. SET jack Entering Your Name and Fax Number Enter your fax number by pressing the number keys max digits Setting the Date and Time Press once and 3 times Daylight Saving Time Setting the reception mode Setting the Reception ModeMode Speaker Volume AdjustmentDesired volume level Press To select Ringer When talking through the handset Press To selectHandset If you selected Ringer OFF OK ? to Sending Faxes Size and weightTransmittable Documents Loading the Document Other restrictions Removing a document from the feeder Open the operation panel Remove the document Resolution settings Adjusting the Resolution and ContrastContrast settings Press RESOLUTION/ one or more times Load the documents Changing the default resolution Sending a Fax by Normal Dialing Sending a Fax by Automatic Dialing Sending a Fax by Automatic Dialing Press Function once Once Storing fax and phone numbers for automatic dialingRapid Keys If you know the Speed Dial number that Memory Date and time display Editing and clearing auto-dial numbersReturn to to store another number, or press to return to Press 1 for Edit or 2 for Clear Press Memory Make the desired changes to the name To the date and time display Rapid Key Dialing Using a Rapid Key for a voice callLoad the documents If desired, press Speed Dialing Using a Speed Dial number for a voice callMemory . If not, press Repeat Step Press Until the name of the other party appears Searching for an auto-dial numberDisplay if no name was stored, the number will appear Sending a fax by Direct Keypad Dialing Correct, press Memory Once. Redial appears in the display, followed by RedialAutomatic redialing Press Redial Error Correction Mode Press Function once Times. Display Batch Page Numbering Sending a Fax From Memory Broadcasting sending a fax to multiple destinations Load the documents If desired, press RESOLUTION/ to set Broadcasting using a Group KeyWhen you are ready to begin transmission, press Memory Press the appropriate Group Key Press To program a Group Key Storing numbers in Group KeysPress To clear a Group Key Press to return to the date and time display Memory transmission If the memory becomes full Receiving Faxes Using FAX ModeChanging the number of rings Using TEL Mode Using TEL Mode Answering on an extension phone connected to the same line Answer the extension phone when it ringsAnswering with the fax’s handset Display shows Receiving and then Fax Signal Receive Optional Reception SettingsPress once and 7 times Changing the number for remote fax activation Press To select AUTO, or 2 to Reception RatioPress Function once and twice Select 100% Substitute Reception to Memory Making Copies Select any of the following copy settings as neededExample of two Copies each Three originals If Memory is Full appears When you are ready to begin copying, pressCopy Cut-off Press Once Twice Connecting an Answering Machine Answering Machine Connection Changing the outgoing message Using the Answering Machine ConnectionSet the reception mode to A.M Set your answering machine to auto answer How answering machine mode operates Optional A.M. Mode SettingsQuiet Detect Time Enter a number from 01 to 10, or enter To turn off the function Press Function once Quiet Detect Start TimePress once and 6 times On TAD Failure Caller ID Requires Subscription to Service Special Functions Enter the three digits of your area code How Caller ID operatesDisplay messages Press Memory to store your area code Press Z twice Voice call Press when you have finished viewing the listViewing the Caller ID list Fax Priority Call To delete calls from the Caller ID listTo store or clear the number Blocking voice calls Distinctive Ring Requires Subscription to Service Set the reception mode to FAX Blocking Reception of Unwanted Faxes Polling Requesting a Fax Transmission Requesting transmission Being polled polling standby Polling security Storing fax numbers for polling permission Enter the fax number maximum of 20 digits Editing and clearing polling permission numbers Press Function once and once Printing ListsActivity Report Press Memory to print the list Group List Setup ListTelephone Number List Caller-ID List Transaction Report Headings in the Transaction Report Transaction Report print condition Auto print-out of Activity Report Press 1 to turn on auto print out, or To turn it off Cleaning the Machine MaintenanceCleaning the scanning glass and rollers Maintenance Cleaning the housing Rotating the white roller Improving Print Quality Aligning the print cartridge Cleaning the print cartridge nozzles Maintenance Wiping the print nozzles and contacts Cleaning the cartridge holder Line error TroubleshootingProblems and Solutions Problem Solution Dialing and transmission problems Trouble- shooting Reception and copying problems 100 General problems Answering machine connection Messages and Signals Press Start KEY 104 Audible signals Recalling Clearing Paper Jams Clearing a jammed document Clearing jammed printing paper Flip down the green levers on each side of the white roller 108 FCC Regulatory Information A R P Material Safety Data Sheet 2/3 Material Safety Data Sheet 3/3 Quick Reference Guide Sending Faxes Guía de referencia rápida Transmisión de documentos Index 115 116 Page Sharp Corporation