Manuals / Sharp / Computer Equipment / Projector

Sharp PG-F325W specifications Controlling the Projector via LAN, Version 5.0 or later

Models: PG-F325W

1 34

Download 34 pages 18.68 Kb

Page 15

Controlling the Projector via LAN

Controlling the Projector via LAN

After connecting the projector to your network, enter the projector IP address in “Address” on Internet Explorer (version 5.0 or later) using a computer on the network to start a setup screen that will enable control of the projector via the network.

Controlling the Projector

Using Internet Explorer

(Version 5.0 or later)

Complete connections to external equipment before starting the operation. (See pages 21- 25 of the projector’s operation manual.)

Complete the AC cord connection. (See page 25 of the projector’s operation manual.)

Note

•When connecting the projector to the LAN, use a commercially available LAN cable (UTP cable, Category 5, cross-over type). When connecting the projector to a hub, use a straight-through cable.

1 Start Internet Explorer (version

5.0 or later) on the computer.

2 Enter “http://” followed by the projector IP address set by the procedure on page 14 followed by “/” in “Address”, and then press the “Enter” key.

•When “DHCP Client” is set to “OFF” on the projector, IP address is 192.168.150.2. If you did not change the IP address in “3. Setting up a Network Connection for the Projector” (pages 13-14), enter “http://192.168.150.2/”.

3

A screen for controlling the pro- jector appears, ready for per- forming various status condi- tions, control, and settings.

-15

Image 15

Sharp PG-F325W Controlling the Projector via LAN, Controlling the Projector Using Internet Explorer, Version 5.0 or later

Contents

Resetting the Lamp Timer of the Projector SETUP MANUALConnecting Pin Assignments RS-232C Specifications and CommandsC3 C5 C4 C2 C1 8 Connecting Pin Assignmentssub 15 pin female connector DVI-I Terminal 29 pin connectorUSB Terminal Type B USB connector Connecting Pin AssignmentsRS-232C Terminal mini DIN 9 pin female connector RS-232C Cable recommended connection D-sub 9 pin female connectorBasic format RS-232C Specifications and CommandsComputer control Communication conditionsP O W R CommandsRS-232C Specifications and Commands Example When turning on the projector, make the following settingRS-232C Specifications and Commands RS-232C Specifications and Commands 3 The Lamp Timer Reset command is available only in standby mode RS-232C Specifications and Commands2. Setting an IP address for the computer Setting up the Projector Network EnvironmentNetwork settings on the computer 1. Connecting the projector to a computer4 Turn on the computer 1. Connecting the Pro- jector to a ComputerSetting up the Projector Network Environment 3 Plug the power cord into the AC socket of the projectorSetting up the Projector Network Environment 2. Setting an IP Address for the Computer2 Click “start”, and click “Control Panel” Click “Properties”Setting up the Projector Network Environment IP address Subnet mask Default gateway Do not input any values5 Click “Internet Protocol Version 4 TCP/IPv4”, and click the “Properties” button3. Setting up a Network Connection for the Projector 1 Start Internet Explorer versionSetting up the Projector Network Environment Setting up the Projector Network Environment Click the “Apply” button1 Start Internet Explorer version 5.0 or later on the computer Controlling the Projector Using Internet ExplorerControlling the Projector via LAN Version 5.0 or laterControlling the Projector MAC Address Power Condition Lamp Timer Lamp Life Input Signal InfoPower Input Select Volume AV Mute Confirming the ProjectorSetup Guide Setting and Adjusting theSetting the Security Projector Settings & AdjustmentsOn this screen, you can make general settings relating to the network Making General Settings for the Network NetworkSetting for Sending E-mail when an Error Occurs Mail - Originator SettingsControlling the Projector via LAN Mail - Recipient SettingsOccurs Service & Support Access URL Example of the display when an error occurs“Password” is displayed. Input the password and press the“Enter”key Setting up the Projector Using RS-232C or TelnetWhen Connecting Using RS-232C 7 Input “setup” and press the “Enter” key5 “Password” is displayed. Input the password and press the“Enter”key When Connecting Using TelnetSetting up the Projector Using RS-232C or Telnet 6 Input “setup” and press the “Enter” key4User Name Factory default setting Not Re- quired SETUP MENU Main MenuADVANCED SETUP MENU 3Default Gateway3 Enter “v” and press the “Enter” key to verify setting detail list View Setting Detail ListVView All Setting 1 Enter “v” and press the “Enter” key. Display all setting valuestings QQuit Unchanged Save Settings and QuitQuit without Saving Set SSave & QuitUser Name Setting IP Address SettingDefault Gateway Setting Subnet Mask Setting5Password Password SettingProjector Name Setting DHCP Client SettingData Port Setting Disconnecting All ConnecSetting Auto Logout Time Entering ADVANCED SETUP MENUADVANCED5Network Ping Test Setting of Accept IP Ad- dressCarrying out Network Ping Test Accepting All IP Addresses1 Enter “q” and press the “Enter” key. Returns to the SETUP MENU Setting of Search PortReturn to Default Settings ADVANCED!Restore Default Setting2 Enter a name in the “Name” field, and click “OK” Resetting the Lamp Timer of the Projector via LAN5 Click “Properties” on the “File” menu Resetting the Lamp Timer of the Projector via LAN6 Click the “Settings” tab, and then click “ASCII Setup” Send the lamp reset command “LPRE0001”Communication cannot be established with the projector TroubleshootingWhen connecting the projector using serial-connection Check the network settings for the computer and the projectorTroubleshooting Troubleshooting