Manuals / Sharp / Computer Equipment / Projector

Sharp PG-F325W Save Settings and Quit, Quit without Saving Set, SSave & Quit, Setup Menu

Models: PG-F325W

1 34

Download 34 pages 18.68 Kb

Page 24

Save Settings and Quit

Setting up the Projector Using RS-232C or Telnet

Save Settings and Quit

([S]Save & Quit)

Save set values and quit menu.

▼SETUP MENU

---------------------------------	SETUP MENU--------------------------------
[1]IP Address	[2]Subnet Mask	[3]Default Gateway
[4]User Name	[5]Password
[6]RS-232C Baud Rate	[7]Projector Name [8]DHCP Client
[A]Advanced Setup		[D]Disconnect All
[V]View All Setting	[S]Save & Quit	[Q]Quit Unchanged
setup>s		1
All Connection will be disconnect.
Continue(y/n)? y		2
Apply New setting...Done.

Quit without Saving Set-

tings ([Q]Quit Unchanged)

Quit menu without saving setting values.

▼SETUP MENU

---------------------------------	SETUP MENU--------------------------------
[1]IP Address	[2]Subnet Mask	[3]Default Gateway
[4]User Name	[5]Password
[6]RS-232C Baud Rate [7]Projector Name		[8]DHCP Client
[A]Advanced Setup		[D]Disconnect All
[V]View All Setting	[S]Save & Quit	[Q]Quit Unchanged
setup>q		1
Quit Without Saving(y/n)? y		2
Setting Unchanged.

1Enter “s” and press the “Enter” key.

2 Enter “y” and press the “Enter” key.

1Enter “q” and press the “Enter” key.

2 Enter “y” and press the “Enter” key.

-24

Image 24

Sharp PG-F325W Save Settings and Quit, Quit without Saving Set, SSave & Quit, tings QQuit Unchanged, Setup Menu

Contents

SETUP MANUAL Connecting Pin AssignmentsRS-232C Specifications and Commands Resetting the Lamp Timer of the ProjectorConnecting Pin Assignments sub 15 pin female connectorDVI-I Terminal 29 pin connector C3 C5 C4 C2 C1 8Connecting Pin Assignments RS-232C Terminal mini DIN 9 pin female connectorRS-232C Cable recommended connection D-sub 9 pin female connector USB Terminal Type B USB connectorRS-232C Specifications and Commands Computer controlCommunication conditions Basic formatCommands RS-232C Specifications and CommandsExample When turning on the projector, make the following setting P O W RRS-232C Specifications and Commands RS-232C Specifications and Commands RS-232C Specifications and Commands 3 The Lamp Timer Reset command is available only in standby modeSetting up the Projector Network Environment Network settings on the computer1. Connecting the projector to a computer 2. Setting an IP address for the computer1. Connecting the Pro- jector to a Computer Setting up the Projector Network Environment3 Plug the power cord into the AC socket of the projector 4 Turn on the computer2. Setting an IP Address for the Computer 2 Click “start”, and click “Control Panel”Click “Properties” Setting up the Projector Network EnvironmentIP address Subnet mask Default gateway Do not input any values 5 Click “Internet Protocol Version4 TCP/IPv4”, and click the “Properties” button Setting up the Projector Network Environment3. Setting up a Network Connection for the Projector 1 Start Internet Explorer versionSetting up the Projector Network Environment Click the “Apply” button Setting up the Projector Network EnvironmentControlling the Projector Using Internet Explorer Controlling the Projector via LANVersion 5.0 or later 1 Start Internet Explorer version 5.0 or later on the computerMAC Address Power Condition Lamp Timer Lamp Life Input Signal Info Power Input Select Volume AV MuteConfirming the Projector Controlling the ProjectorSetting and Adjusting the Setting the SecurityProjector Settings & Adjustments Setup GuideMaking General Settings for the Network Network Setting for Sending E-mail when an Error OccursMail - Originator Settings On this screen, you can make general settings relating to the networkMail - Recipient Settings Occurs Service & Support Access URLExample of the display when an error occurs Controlling the Projector via LANSetting up the Projector Using RS-232C or Telnet When Connecting Using RS-232C7 Input “setup” and press the “Enter” key “Password” is displayed. Input the password and press the“Enter”keyWhen Connecting Using Telnet Setting up the Projector Using RS-232C or Telnet6 Input “setup” and press the “Enter” key 5 “Password” is displayed. Input the password and press the“Enter”keySETUP MENU Main Menu ADVANCED SETUP MENU3Default Gateway 4User Name Factory default setting Not Re- quiredView Setting Detail List VView All Setting1 Enter “v” and press the “Enter” key. Display all setting values 3 Enter “v” and press the “Enter” key to verify setting detail listSave Settings and Quit Quit without Saving SetSSave & Quit tings QQuit UnchangedIP Address Setting Default Gateway SettingSubnet Mask Setting User Name SettingPassword Setting Projector Name SettingDHCP Client Setting 5PasswordDisconnecting All Connec Setting Auto Logout TimeEntering ADVANCED SETUP MENU Data Port SettingSetting of Accept IP Ad- dress Carrying out Network Ping TestAccepting All IP Addresses ADVANCED5Network Ping TestSetting of Search Port Return to Default SettingsADVANCED!Restore Default Setting 1 Enter “q” and press the “Enter” key. Returns to the SETUP MENUResetting the Lamp Timer of the Projector via LAN 2 Enter a name in the “Name” field, and click “OK”Resetting the Lamp Timer of the Projector via LAN 6 Click the “Settings” tab, and then click “ASCII Setup”Send the lamp reset command “LPRE0001” 5 Click “Properties” on the “File” menuTroubleshooting When connecting the projector using serial-connectionCheck the network settings for the computer and the projector Communication cannot be established with the projectorTroubleshooting Troubleshooting