SonicWALL Network Security Appliances
Getting Started Guide
NSA 5000/4500/3500
NETWORK SECURITY
1Pre-ConfigurationTasks - page
Document Contents
4Additional Deployment Configuration - page
6Product Safety and Regulatory Information - page
Back
SonicWALL NSA Series
Front
In this Section
Pre-ConfigurationTasks
Any Items Missing?
Check Package Contents
Administrator Information
Obtain Configuration Information
Obtain Internet Service Provider ISP Information
Registration Information
Feature
The Front Panel
Reset Button
AlarmLED Indicates an alarm condition
Icon Feature
The Back Panel
Power Supply
Description
Page 8 The Back Panel
In this Section
Page 10 Before You Register
Before You Register
Licensing Security Services and Software - page
Product Registration
Product Registration - page
Registration Next Steps - page
Licensing Security Services and Software
To purchase a product or service, click Buy Now
Registration Next Steps
Registering a Second Appliance as a Backup
Accessing the Management Interface - page
Enabling Security Services in SonicOS - page
In this Section
Deployment Scenarios
Current Gateway Configuration
Selecting a Deployment Scenario
New Gateway Configuration
Use Scenario
Scenario A NAT/Route Mode Gateway
Page 18 Selecting a Deployment Scenario
Scenario B State Sync Pair in NAT/Route Mode
CThird Party Gateway
Scenario C L2 Bridge Mode
Connecting the WAN Port
Initial Setup
System Requirements
Connecting the WAN Port - page
Applying Power
Connecting the LAN Port
Accessing the Setup Wizard
Accessing the Management Interface
Testing Your Connection
Connecting to Your Network
Enabling Security Services in SonicOS - page
Activating Licenses in SonicOS
Upgrading Firmware on Your SonicWALL
Saving a Backup Copy of Your Preferences
Obtaining the Latest Firmware
Saving a Backup Copy of Your Preferences - page
Using SafeMode to Upgrade Firmware
Upgrading the Firmware with Current Settings
Upgrading the Firmware with Factory Defaults
If You Are Following
Uploaded Firmware - New
Proceed to Section
Scenario
Initial High Availability Setup
Configuring a State Sync Pair in NAT/Route Mode
Initial High Availability Setup - page
Configuring High Availability - page
Configuring Advanced HA Settings
Configuring High Availability
5.Optionally adjust the Heartbeat Interval to control how often the two units communicate. The default is 5000 milliseconds the minimum recommended value is 1000 milliseconds. Less than this may cause unnecessary failovers, especially when the SonicWALL is under a heavy load
Synchronizing Settings
Synchronizing Firmware
Adjusting High Availability Settings
HA License Configuration Overview
8.Click Register
Associating Pre-RegisteredAppliances
Configuring the Primary Bridge Interface
Configuring L2 Bridge Mode
Connection Overview
Connection Overview - page
If You Are Following
Configuring the Secondary Bridge Interface
Proceed to Section
Scenario
In this Section
Additional Deployment Configuration
Creating Network Access Rules
3.In the Add Rule page in the General tab, select Allow Deny Discard from the Action list to permit or block IP traffic
Creating a NAT Policy
Before configuring NAT Policies, you must create all Address Objects associated with the policy. For instance, if you are creating a One-to-OneNAT policy, first create Address Objects for your public and private IP addresses
Configuring Address Objects
6.For Original Service, select Any
Configuring NAT Policies
7.For Translated Service, select Original
2.For Original Source, select Any
Enabling Gateway Anti-Virus
Enabling Security Services in SonicOS
Enabling Intrusion Prevention Services - page
Enabling Gateway Anti-Virus - page
Restrict Transfer of password-protectedZip files - Disables the transfer of password protected ZIP files over any enabled protocol. This option only functions on protocols that are enabled for inspection
Enabling Intrusion Prevention Services
Enabling Anti-Spyware
Applying Security Services to Network Zones
Configuring SonicPoint Provisioning Profiles
Deploying SonicPoints for Wireless Access
Updating SonicPoint Firmware
Configuring a Wireless Zone - page
2.In the 802.11g Radio tab Select Enable Radio
Select Enable SonicPoint
Configuring a Wireless Zone
Assigning an Interface to the Wireless Zone
SonicOS Enhanced Administrator’s Guide
Connecting the SonicPoint
Using Packet Capture
Troubleshooting Diagnostic Tools
Using Packet Capture - page Using Ping - page
Using the Active Connections Monitor - page
Using Ping
Page 56 Troubleshooting Diagnostic Tools
Using the Active Connections Monitor
Using Log View
See this Chapter
Deployment Configuration Reference Checklist
For this Task
Customer Support - page Support Services - page
Support and Training Options
In this Section
SonicWALL Live Product Demos - page
Page 60 Customer Support
Support Services
Customer Support
Knowledge Portal
SonicWALL Live Product Demos
User Forums
E-Training Instructor-LedTraining
Training
Custom Training Technical Certification
Authorized Training Partners
SonicOS Enhanced Administrator’s Guide
Related Documentation
SonicOS Enhanced Feature Modules
SonicWALL GVC 4.0 Administrator’s Guide
In this Section
Product Safety and Regulatory Information
Lithium Battery Warning
Safety and Regulatory Information
Rack Mounting the SonicWALL
Cable Connections
Weitere Hinweise zur Montage
Safety and Regulatory Information in German
Hinweis zur Lithiumbatterie
Kabelverbindungen
Canadian Radio Frequency Emissions Statement
FCC Part 15 Class A Notice
CISPR 22 EN 55022 Class A
Regulatory Information for Korea
Trademarks
Copyright Notice
Page 70 Notes
Page
Page 72 Notes
SonicWALL, Inc
P/N Rev A 01/08
