BVideo/audio input setting section

 

INPUT SELECT

 

SDTI/i.LINK

VIDEO

CH1 1/2

CH2 3/4

d CH2 3/4 button

c CH1 1/2 button

bVIDEO button

aSDTI/i.LINK button

aSDTI/i.LINK (SDTI (QSDI) interface/i.LINK

selection) button

Each press of this button cycles through the following input signal selection options.

•Digital video signal in SDTI (QSDI) format input to the SDI/SDTI (QSDI) IN connector (optional DSBK-1501 board required)

When this is selected, use the CH1 1/2 button and CH2 3/4 button to select the required input audio signals.

Note

In this case, the phases of the selected audio signals will be about two frames ahead of the phase of the digital video signal in SDTI (QSDI) format.

•Digital video and audio signals in SDTI (QSDI) format input to the SDI/SDTI (QSDI) IN connector (optional DSBK-1501 board required)

•Digital video and audio signals in i.LINK-compatible DV format input to the i.DV IN/OUT connector

The selection made with this button is indicated in the INPUT signal display section (see page 18).

bVIDEO button

Each press of this button cycles through the following input video signal selection options.

•Composite video signal input to the VIDEO IN connector (optional DSBK-1504/1504P board required)

•S-video (separated Y and C) signals input to the VIDEO IN connectors (optional DSBK-1504/1504P board required)

•Y, R−Y and B−Y component video signals input to the VIDEO IN connectors (optional DSBK-1504/1504P board required)

•SDI video signal input to the SDI/SDTI (QSDI) IN connector (optional DSBK-1501 board required)

•Video test signal (selected with the INT VIDEO SG

menu item (see page 70)) generated by the internal signal generator

The selection made with this button is indicated by the VIDEO indicators in the INPUT signal display section (see page 17).

cCH1 1/2 (audio channel 1 or 1/2) button

Each press of this button cycles through the following input audio signal selection options for audio channel 1 (when in 2-channel mode) or for audio channels 1 and 2 (when in 4-channel mode).

•Analog audio signal input to the AUDIO IN 1/3 connector (optional DSBK-1504/1504P board required)

•Digital audio signal in AES/EBU format input to the AUDIO (AES/EBU) IN 1/2 connector (optional DSBK- 1501 board required)

•SDI audio signal input to the SDI/SDTI (QSDI) IN connector (optional DSBK-1501 board required)

•Audio test signal (selected with the INT AUDIO SG menu item (see page 72) generated by the internal signal generator

The selection made with this button is indicated by the AUDIO CH-1 1/2 indicators in the INPUT signal display section (see page 17).

When analog audio is selected (optional DSBK-1504/ 1504P board required), the signal input to the AUDIO IN 1/3 connector is recorded either on channel 1 (when in 2- channel mode) or on channels 1 and 3 (when in 4-channel mode). That is, in 4-channel mode, the same analog audio signal is recorded on channels 1 and 3. Using the REC/PB LEVEL control knobs with the VAR switch set to REC, it is possible to adjust the audio levels on the two channels separately.

You can switch the audio recording mode with the REC MODE menu item (see page 71). The selection is indicated by the REC MODE display on the front panel.

dCH2 3/4 (audio channel 2 or 3/4) button

Each press of this button cycles through the following input audio signal selection options for audio channel 2 (when in 2-channel mode) or for audio channels 3 and 4 (when in 4-channel mode).

•Analog audio signal input to the AUDIO IN 2/4 connector (optional DSBK-1504/1504P board required)

•Digital audio signal in AES/EBU format input to the AUDIO (AES/EBU) IN 3/4 connector (optional DSBK- 1501 board required)

•SDI audio signal input to the SDI/SDTI (QSDI) IN connector (optional DSBK-1501 board required)

•Audio test signal (selected with the INT AUDIO SG menu item (see page 72) generated by the internal signal

generator

The selection made with this button is indicated by the AUDIO CH-2 3/4 indicators in the INPUT signal display section (see page 17).

When analog audio is selected (optional DSBK-1504/ 1504P board required), the signal input to the AUDIO IN 2/4 connector is recorded either on channel 2 (when in 2- channel mode) or on channels 2 and 4 (when in 4-channel mode). That is, in 4-channel mode, the same analog audio signal is recorded on channels 2 and 4. Using the REC/PB LEVEL control knobs with the VAR switch set to REC, it

Overview 1 Chapter

Location and Function of Parts

15