Installing and Connecting the Projection TV (continued)
Disconnect all power sources before making any connections.
Connecting an audio system (Upper illustration)
For more dynamic sound, connect an audio system to the projection TV.
1Using an AUDIO cable, connect AUDIO (VAR/FIX) OUT on the projection TV to one of the unused Line inputs (e.g.
2Set the stereo to the chosen Line input and use the Audio menu to set the audio output and switch the TV’s speakers off. (see “Salida de audio” and “Parlantes” on page 22)
Note:
(Rear of projection TV)
|
| IN |
|
|
| VIDEO 1 | VIDEO 3 |
|
|
|
|
| OUT |
|
| S VIDEO |
| MONITOR AUDIO |
|
|
|
| (VAR/FIX) |
|
| VIDEO | Y | VIDEO | |
| (MONO) |
| (MONO) | (white) |
| L |
| L |
|
| AUDIO |
| AUDIO |
|
CONTROL S | R |
| R |
|
OUT |
|
| ||
|
|
|
| |
|
| COMPONENT |
|
|
Stereo amplifier
HRD
Line inputs
•You can adjust VOLUME, “Graves,” “Agudos,” “Balance,” “MTS/SAP” and “Efecto” with the supplied remote control. The control items except VOLUME can be adjusted only when “Salida de audio” is set to “Variable” in the Audio menu. (see “Salida de audio” on page 22)
Connecting a Sony SAVA series speaker system (Lower illustration)
Use this connection to control the speaker’s Dolby Pro Logic surround system and super woofer mode with the remote control. (see “Control SAVA SP ” on page 22)
1Using the AUDIO cable supplied with the speaker to AUDIO (VAR/FIX) OUT on the projection TV.
2Using the CONTROL S cable, connect CONTROL S IN on the speaker to CONTROL S OUT on the projection TV.
1 0
| |
(red) | (not supplied) |
(Rear of projection TV)
SAVA series
speaker system
|
| IN |
|
|
|
|
| VIDEO 1 VIDEO 3 |
|
|
|
|
| OUT |
| ||
| S VIDEO | MONITOR AUDIO |
| ||
|
| (VAR/FIX) | (white) |
|
|
| VIDEO |
|
| 1 IN L | |
| Y | VIDEO | 1 | ||
| L | PB | L |
| |
| (MONO) | (MONO) |
| ||
| AUDIO |
| AUDIO |
|
|
CONTROL S | R | PR | R |
|
|
OUT |
|
|
|
| 1 IN R |
|
| COMPONENT |
|
| |
CONTROLS | Audio cord supplied | ||||
OUT |
| with the speakers | |||
|
|
|
|
| 2 |
CONTROL S IN
Basic Set Up
Using the Remote Control
Inserting the batteries
Insert two size AA (R6) batteries (supplied) by matching the + and – on the batteries to the diagram inside the remote control’s battery compartment.
Notes:
•Remove the batteries to avoid damage from possible battery leakage whenever you anticipate that the remote control will not be used for an extended period.
•Handle the remote control with care. Avoid dropping it, getting it wet, or placing it in direct sunlight, near a heater or where the humidity is high.
•Your remote control can be programmed to operate most video equipment.
(see “Operating Video Equipment” on page 30)
Setting Up the Projection TV Automatically
The AUTO SET UP feature will allow you to set the
The AUTO SET UP feature does not apply for installations that use a cable box for all channel selection.
You can also set up the projection TV manually. (see “Using the Ajuste de canal Menu” on pages 24 and 25)
Notes:
•Before you perform AUTO SET UP again, make sure that the input from ANT (not AUX) is selected by pressing ANT until “AUX” does not appear next to the channel number.
•Perform this function during the day, with the antenna and/or cable properly connected, to ensure that all available channels will be broadcasting and receivable.
•When you perform AUTO SET UP, all the settings in the Video, and Audio menus are reset to the factory settings.
(continued)
1 1
– 12 –
